Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Smart Entry and Start System) › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328238 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B460711N02
3.333,0.375 3.802,0.635 0.469,0.26 3.458,0.427 3.917,0.625 0.458,0.198 10 false K60

a.

Disconnect the K60 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
K60-4 (+B) - K60-12 (GND) Input LA-GR - W-B Battery Always 11 to 14 V +B
K60-5 (KSW) - K60-12 (GND) Input B - W-B Unlock warning switch signal No door control transmitter assembly in ignition key cylinder 10 kΩ or higher
·

B2780

·

Key SW


Door control transmitter assembly in ignition key cylinder Below 1 Ω
K60-12 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the K60 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
K60-6 (IG) - K60-12 (GND) Input L - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
K60-8 (IND) - K60-12 (GND) Output W - W-B Security indicator signal No door control transmitter assembly in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Door control transmitter assembly in ignition key cylinder (immobiliser system unset) Below 1 V
K60-9 (D) - K60-12 (GND) Input/Output L - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
K60-2 (ANT1) - K60-12 (GND) Input/Output R - W-B Transponder key amplifier power source No door control transmitter assembly in ignition key cylinder Below 1 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 1)
K60-3 (ANT2) - K60-12 (GND) Input/Output W - W-B Transponder key amplifier communication signal No door control transmitter assembly in ignition key cylinder Below 1 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 2)
K60-10 (EFII) - K60-12 (GND) Input LG - W-B ECM input signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
K60-11 (EFIO) - K60-12 (GND) Output L - W-B ECM output signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection K60-2 (ANT1) - K60-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection K60-3 (ANT2) - K60-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection K60-10 (EFII) - K60-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection K60-11 (EFIO) - K60-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM


A412929N01
2.448,0.365 2.844,0.635 0.396,0.271 5.75,0.385 6.125,0.656 0.375,0.271 2.51,0.406 2.958,0.667 0.448,0.26 10 false C58 5.792,0.417 6.198,0.656 0.406,0.24 10 false A22

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
A22-45 (IMO) - C58-59 (E1) Output V - W-B Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
A22-28 (IMI) - C58-59 (E1) Input GR - W-B Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C01
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A22-45 (IMO) - C58-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A22-28 (IMI) - C58-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal