Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2017.09–2019.10
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) U

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  TERMINALS OF ECM  


B460712E06
5.49,0.917 5.823,1.156 0.333,0.24 2.01,0.917 2.385,1.156 0.375,0.24 3.885,0.927 4.26,1.167 0.375,0.24 5.531,0.958 5.99,1.156 0.458,0.198 10 false A24 2.083,0.958 2.542,1.156 0.458,0.198 10 false C57 3.958,0.969 4.417,1.167 0.458,0.198 10 false C59

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-1 (BATT) - A24-10 (E1) G - W-B Battery (for measuring battery voltage and ECM memory) Always 11 to 14 V
A24-2 (IGSW) - A24-10 (E1) B - W-B Engine switch signal Engine switch on (IG) 11 to 14 V
A24-3 (VPMP) - A24-10 (E1) L - W-B Vent valve (built into canister pump module) Engine switch on (IG) 11 to 14 V
A24-5 (MPMP) - A24-10 (E1) V - W-B Leak detection pump (canister pump module) Leak detection pump OFF Below 3 V
Leak detection pump ON 11 to 14 V
A24-6 (FPC) - A24-10 (E1) R - W-B Fuel pump control Engine switch on (IG) Below 1.5 V
A24-8 (CANH) - A24-10 (E1) B - W-B CAN communication line Engine stopped, engine switch on (IG) Pulse generation
(See waveform 1)
A24-9 (+B) - A24-10 (E1) L - W-B
·

Power source of ECM

·

Power source of throttle actuator


Engine switch on (IG) 11 to 14 V
A24-10 (E1) - Body ground W-B - - Ground Always Below 1 Ω
A24-14 (S) - A24-10 (E1) GR - W-B S shift position switch signal Engine switch on (IG), shift lever in S 11 to 14 V
Engine switch on (IG), shift lever not in S Below 1.5 V
A24-15 (MREL) - A24-10 (E1) W - W-B EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) Below 1.5 V
A24-16 (NEO) - A24-10 (E1) B - W-B Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 2)
A24-18 (CANL) - A24-10 (E1) W - W-B CAN communication line Engine stopped, engine switch on (IG) Pulse generation
(See waveform 3)
A24-21 (STP) - A24-10 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A24-22 (ST1-) - A24-10 (E1) LG - W-B Stop light switch assembly signal
(opposite to STP terminal)
Engine switch on (IG), brake pedal depressed 0 to 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
A24-23 (NSW) - A24-10 (E1) BE - W-B Park/Neutral position switch assembly signal Engine switch on (IG), shift lever not in P or N 11 to 14 V
Engine switch on (IG), shift lever in P or N Below 3.0 V
A24-30 (STA) - A24-10 (E1) G - W-B Starter assembly signal Cranking 6.0 V or higher
A24-32 (RFC) - A24-10 (E1) LG - W-B Cooling fan control signal Engine switch on (IG), A/C switch on (max cool) Pulse generation
(See waveform 4)
A24-34 (IREL) - A24-10 (E1) P - W-B D INJ relay operation signal Engine switch on (IG) Below 1.5 V
A24-35 (+B2) - A24-10 (E1) L - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
A24-36 (E2) - Body ground W-B - - Ground Always Below 1 Ω
A24-39 (KSW) - A24-10 (E1) R - W-B Electrical key in vehicle signal Electrical key outside vehicle 11 to 14 V
A24-42 (SPD) - A24-10 (E1) L - W-B Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A24-45 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A24-48 (VCPP) - A24-49 (EPPM) B - LG Power source for canister pressure sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
A24-50 (PPMP) - A24-49 (EPPM) P - LG Canister pressure sensor (built into canister pump module) Engine switch on (IG) 3.0 to 3.6 V
A24-52 (TC) - A24-10 (E1) GR - W-B Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
A24-53 (+BD1) - A24-10 (E1) W - W-B Power source of ECU (injector driver) Engine switch on (IG) 11 to 14 V
A24-54 (E1D1) - Body ground W-B - - Ground Always Below 1 Ω
A24-55 (VPA) - A24-56 (EPA) G - L Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 2.6 to 4.5 V
A24-57 (VCPA) - A24-56 (EPA) BE - L Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A24-58 (VPA2) - A24-59 (EPA2) GR - P Accelerator pedal position sensor signal Engine switch on (IG), accelerator pedal fully released 1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 4.75 V
A24-60 (VCP2) - A24-59 (EPA2) SB - P Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
C59-23 (D) - A24-10 (E1) R - W-B D shift position switch signal Engine switch on (IG), shift lever in D or S 11 to 14 V
Engine switch on (IG), shift lever not in D or S Below 1 V
C59-24 (N) - A24-10 (E1) LG - W-B N shift position switch signal Engine switch on (IG), shift lever in N 11 to 14 V
Engine switch on (IG), shift lever not in N Below 1 V
C59-25 (R) - A24-10 (E1) W - W-B R shift position switch signal Engine switch on (IG), shift lever in R 11 to 14 V
Engine switch on (IG), shift lever not in R Below 1 V
C59-26 (P) - A24-10 (E1) B - W-B P shift position switch signal Engine switch on (IG), shift lever in P 11 to 14 V
Engine switch on (IG), shift lever not in P Below 1 V
C57-1 (M-) - A24-10 (E1) L - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 6)
C57-2 (M+) - A24-10 (E1) B - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 7)
C57-3 (EGA+) - A24-10 (E1) R - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
C57-4 (EGA-) - A24-10 (E1) L - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
C57-5 (EGB-) - A24-10 (E1) V - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
C57-6 (EGB+) - A24-10 (E1) GR - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
C57-7 (HTHM) - A24-10 (E1) G - W-B Thermostat heater (water inlet with thermostat sub-assembly) operation signal Engine switch on (IG) 11 to 14 V
C57-8 (HA1B) - A24-10 (E1) R - W-B Air fuel ratio sensor (sensor 2) heater operation signal Engine switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 9)
C57-9 (HA1A) - A24-10 (E1) L - W-B Air fuel ratio sensor (sensor 1) heater operation signal Engine switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 10)
C57-10 (#2D-) - A24-10 (E1) G - W-B Direct fuel injector assembly signal (No. 2 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-11 (#2D+) - A24-10 (E1) L - W-B Direct fuel injector assembly signal (No. 2 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-12 (#3D+) - A24-10 (E1) W - W-B Direct fuel injector assembly signal (No. 3 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-13 (#3D-) - A24-10 (E1) R - W-B Direct fuel injector assembly signal (No. 3 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-14 (#4D-) - A24-10 (E1) V - W-B Direct fuel injector assembly signal (No. 4 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-15 (#4D+) - A24-10 (E1) P - W-B Direct fuel injector assembly signal (No. 4 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-16 (#1D+) - A24-10 (E1) W - W-B Direct fuel injector assembly signal (No. 1 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-17 (#1D-) - A24-10 (E1) BR - W-B Direct fuel injector assembly signal (No. 1 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C57-18 (FP1-) - A24-10 (E1) L - W-B Fuel pump assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 12)
C57-19 (FP1+) - A24-10 (E1) G - W-B Fuel pump assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 12)
C57-21 (VOP+) - A24-10 (E1) G - W-B Oil pressure control valve operation signal Idling with warm engine Pulse generation
(See waveform 13)
C57-20 (VOP-) - A24-10 (E1) P - W-B Oil pressure control valve operation signal Idling with warm engine Pulse generation
(See waveform 13)
C57-26 (OE1+) - C57-25 (OE1-) P - L Cam timing oil control solenoid assembly operation signal Idling Pulse generation
(See waveform 14)
C57-28 (EDT1) - A24-10 (E1) P - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 15)
C57-41 (WSV2) - A24-10 (E1) LG - W-B Flow shutting valve (for ATF control) operation signal Engine switch on (IG) 11 to 14 V
C57-42 (WSV1) - A24-10 (E1) W - W-B Flow shutting valve (for heater control) operation signal Engine switch on (IG) 11 to 14 V
C57-44 (ACM) - A24-10 (E1) G - W-B Vacuum switching valve (for active control engine mount system) operation signal Engine switch on (IG) 11 to 14 V
C57-46 (IGT4) - A24-10 (E1) B - W-B No. 4 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C57-47 (IGT3) - A24-10 (E1) P - W-B No. 3 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C57-48 (IGT2) - A24-10 (E1) V - W-B No. 2 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C57-49 (IGT1) - A24-10 (E1) W - W-B No. 1 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C57-50 (WPO) - A24-10 (E1) LG - W-B Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 17)
C57-51 (WPI) - A24-10 (E1) B - W-B Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 18)
C57-66 (PRG) - A24-10 (E1) P - W-B Purge VSV operation signal Engine switch on (IG) 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 19)
C57-70 (EMR1) - A24-10 (E1) LG - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 20)
C57-71 (EMF1) - A24-10 (E1) B - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Below 5.0 V
C57-72 (EMD1) - A24-10 (E1) L - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 21)
C57-73 (#40) - A24-10 (E1) P - W-B Port fuel injector assembly signal (No. 4 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 22)
C57-74 (#30) - A24-10 (E1) W - W-B Port fuel injector assembly signal (No. 3 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 22)
C57-75 (#20) - A24-10 (E1) G - W-B Port fuel injector assembly signal (No. 2 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 22)
C57-76 (#10) - A24-10 (E1) B - W-B Port fuel injector assembly signal (No. 1 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 22)
C57-78 (VCVG) - A24-10 (E1) R - W-B Power source of mass air flow meter sub-assembly (specific voltage) Engine switch on (IG) 4.8 to 5.2 V
C57-84 (VCPF) - A24-10 (E1) LG - W-B Power source of fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-87 (VTA2) - C57-110 (ETA) V - G Throttle position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
C57-88 (VCV1) - A24-10 (E1) L - W-B Power source of camshaft position sensor (for intake camshaft) (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-90 (VV1+) - C57-89 (VV1-) B - LG Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 23)
C57-91 (EV1+) - C57-114 (EV1-) V - G Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 23)
C57-93 (NE+) - C57-115 (NE-) L - P Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 24)
C57-94 (A1A-) - A24-10 (E1) G - W-B Air fuel ratio sensor (sensor 1) signal Engine switch on (IG) 1.24 to 4.22 V
C57-95 (A1A+) - A24-10 (E1) R - W-B Air fuel ratio sensor (sensor 1) signal Engine switch on (IG) 1.46 to 4.22 V
C57-97 (PR) - C57-96 (EPR) L - V Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
C57-98 (VCPR) - C57-96 (EPR) LG - V Power source of fuel pressure sensor (for high pressure side) (specific voltage) Engine switch on (IG) 4.75 to 5.25 V
C57-99 (VCPE) - C57-100 (EPEO) R - G Power source of engine oil pressure sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-101 (VG) - C57-79 (E2G) W - G Mass air flow meter sub-assembly signal Engine switch on (IG) Pulse generation
(See waveform 25)
C57-102 (THA) - C57-79 (E2G) V - G Intake air temperature sensor (mass air flow meter sub-assembly) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C57-107 (PFL) - C57-61 (EPFL) V - L Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) signal Idling with warm engine 0.75 to 4.5 V
C57-108 (VTA1) - C57-110 (ETA) P - G Throttle position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
C57-109 (VCTA) - C57-110 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-111 (KNK1) - C57-112 (EKNK) B - W Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 26)
C57-113 (VCE1) - A24-10 (E1) L - W-B Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-116 (VCNE) - A24-10 (E1) V - W-B Power source of crankshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C57-117 (A1B-) - A24-10 (E1) W - W-B Air fuel ratio sensor (sensor 2) signal Engine switch on (IG) 1.17 to 4.49 V
C57-118 (A1B+) - A24-10 (E1) B - W-B Air fuel ratio sensor (sensor 2) signal Engine switch on (IG) 1.53 to 5.96 V
C57-120 (PIM) - C57-119 (EPIM) P - G Manifold absolute pressure sensor signal Engine switch on (IG) 3.0 to 4.5 V
C57-121 (VCPM) - C57-119 (EPIM) B - G Power source of manifold absolute pressure sensor (specific voltage) Engine switch on (IG) 4.75 to 5.25 V
C57-122 (PEO) - C57-100 (EPEO) W - G Oil pressure sensor signal Idling with warm engine 0.5 to 4.5 V
C57-123 (THEO) - C57-104 (ETHE) V - W Engine oil temperature sensor signal Engine switch on (IG) 0.14 to 4.93 V
C57-125 (THW) - C57-124 (ETHW) L - P Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V

WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A287796E25
2.594,1.656 3.052,1.854 0.458,0.198 10 false GND 2.458,0.302 3.177,0.531 0.719,0.229 10 false 2 V/DIV. 1.167,1.927 2,2.135 0.833,0.208 10 false 2 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 2 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A282867E17
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 2.615,0.24 3.26,0.521 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Engine switch on (IG), A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 5


A283573E11
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Operation Signal (Negative Terminal)
ECM Terminal Name Between M- and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 7


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Operation Signal (Positive Terminal)
ECM Terminal Name Between M+ and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A405745E03
2.688,0.073 3.302,0.427 0.615,0.354 10 false 5 V/DIV. 1.344,1.896 2.563,2.156 1.219,0.26 10 false 5 μs./DIV. 0.198,0.313 0.813,0.667 0.615,0.354 10 false EGA+ 0.229,1.365 0.844,1.719 0.615,0.354 10 false EGA- 2.74,0.792 3.354,1.146 0.615,0.354 10 false GND 2.75,1.594 3.365,1.948 0.615,0.354 10 false GND 0.167,0.458 0.781,0.813 0.615,0.354 10 false (EGB+) 0.198,1.51 0.813,1.865 0.615,0.354 10 false (EGB-)

EGR Valve Assembly Operation Signal
ECM Terminal Name CH1: Between EGA+ and E1
CH2: Between EGA- and E1
CH1: Between EGB+ and E1
CH2: Between EGB- and E1
Tester Range 5 V/DIV., 5 μs./DIV.
Condition Idling with warm engine

HINT:

When the EGR valve assembly is operating, a waveform is produced at each terminal.



WAVEFORM 9


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 2) Heater Operation Signal
ECM Terminal Name Between HA1B and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 10


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal
ECM Terminal Name Between HA1A and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 11


A405747E01
0.302,0.573 0.76,0.771 0.458,0.198 10 false CH1 0.313,0.938 0.771,1.135 0.458,0.198 10 false CH2 1.208,1.896 2.031,2.146 0.823,0.25 10 false 200 μs./DIV. 2.667,0.094 3.354,0.5 0.688,0.406 10 false 50 V/DIV. 2.781,0.594 3.24,0.792 0.458,0.198 10 false GND 2.771,0.948 3.229,1.146 0.458,0.198 10 false GND

No. 1 (to No. 4) Direct Fuel Injector Assembly Signal
ECM Terminal Name CH1: Between #1D+ and E1
CH2: Between #1D- and E1
CH1: Between #2D+ and E1
CH2: Between #2D- and E1
CH1: Between #3D+ and E1
CH2: Between #3D- and E1
CH1: Between #4D+ and E1
CH2: Between #4D- and E1
Tester Range 50 V/DIV., 200 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 12


A405748E01
2.771,0.094 3.406,0.438 0.635,0.344 10 false 20 V/DIV. 1.26,1.885 2.573,2.177 1.313,0.292 10 false 500 μs./DIV. 0.26,0.406 1.573,0.698 1.313,0.292 10 false FP1+ 0.271,1.083 1.583,1.375 1.313,0.292 10 false FP1- 2.76,0.438 3.135,0.865 0.375,0.427 10 false GND 2.76,1.104 3.135,1.531 0.375,0.427 10 false GND

Fuel Pump Assembly (for High Pressure Side) Signal
ECM Terminal Name CH1: Between FP1+ and E1
CH2: Between FP1- and E1
Tester Range 20 V/DIV., 500 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 13


A405749E01
2.708,0.115 3.281,0.49 0.573,0.375 10 false 5 V/DIV. 1.313,1.885 2.479,2.135 1.167,0.25 10 false 20 ms./DIV. 0.198,0.75 0.771,1.125 0.573,0.375 10 false VOP+ 0.219,1.26 0.792,1.635 0.573,0.375 10 false VOP- 2.76,0.781 3.333,1.156 0.573,0.375 10 false GND 2.76,1.271 3.333,1.646 0.573,0.375 10 false GND

Oil Pressure Control Valve Operation Signal
ECM Terminal Name CH1: Between VOP+ and E1
CH2: Between VOP- and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 14


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 15


A149745E04
2.844,1.802 3.302,2 0.458,0.198 10 false GND 2.667,0.729 3.302,0.938 0.635,0.208 10 false 1 V/DIV. 1.344,2.521 2.281,2.823 0.938,0.302 10 false 5 ms./DIV.

Cam Timing Control Motor with EDU Assembly Signal (EDT Signal)
ECM Terminal Name Between EDT1 and E1
Tester Range 1 V/DIV., 5 ms./DIV.
Condition Idling with warm engine


WAVEFORM 16


A247035E03
2.771,0.135 3.385,0.313 0.615,0.177 10 false 5 V/DIV. 3.031,0.604 3.365,0.781 0.333,0.177 10 false GND 3.031,0.938 3.365,1.115 0.333,0.177 10 false GND 3.031,1.271 3.365,1.448 0.333,0.177 10 false GND 3.031,1.594 3.365,1.771 0.333,0.177 10 false GND 2.052,1.885 2.813,2.073 0.76,0.188 10 false 20 ms./DIV. 0.375,0.604 0.813,0.823 0.438,0.219 10 false IGT1 0.365,0.927 0.802,1.146 0.438,0.219 10 false IGT2 0.365,1.26 0.802,1.479 0.438,0.219 10 false IGT3 0.375,1.583 0.813,1.802 0.438,0.219 10 false IGT4

Ignition Coil Assembly Signal (IGT Signal)
ECM Terminal Name Between IGT (1 to 4) and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the engine water pump assembly speed.



WAVEFORM 18


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump assembly speed increases.



WAVEFORM 19


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 20


A149746E04
2.833,1.844 3.292,2.042 0.458,0.198 10 false GND 2.625,0.729 3.281,0.958 0.656,0.229 10 false 2 V/DIV. 1.333,2.573 2.281,2.813 0.948,0.24 10 false 5 ms./DIV.

Cam Timing Control Motor with EDU Assembly Signal (EMR Signal)
ECM Terminal Name Between EMR1 and E1
Tester Range 2 V/DIV., 5 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 21


A150215E05
2.833,1.823 3.333,2.021 0.5,0.198 10 false GND 1.177,2.521 2.302,2.771 1.125,0.25 10 false 100 ms./DIV. 2.667,0.677 3.302,0.927 0.635,0.25 10 false 2 V/DIV.

Cam Timing Control Motor with EDU Assembly Signal (EMD Signal)
ECM Terminal Name Between EMD1 and E1
Tester Range 2 V/DIV., 100 ms./DIV.
Condition Idling with warm engine


WAVEFORM 22


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

No. 1 (to No. 4) Port Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E1
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine (Data List item "Injection Mode" displaying "Port")

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.




WAVEFORM 23


A255508E20
0.052,0.031 0.656,0.188 0.604,0.156 10 5 V/DIV. 0.167,0.656 0.49,0.823 0.323,0.167 10 CH1 0.156,1.448 0.479,1.615 0.323,0.167 10 CH2 0.094,0.844 0.49,1.052 0.396,0.208 10 (VV1) 0.083,1.604 0.479,1.833 0.396,0.229 10 (EV1) 3.052,0.813 3.396,0.958 0.344,0.146 10 GND 3.052,1.573 3.396,1.719 0.344,0.146 10 GND 1.271,1.865 2.021,2.042 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 24


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 25


A337204E05
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND 1.406,1.958 2.188,2.156 0.781,0.198 10 false 100 μs./DIV. 2.813,0.167 3.406,0.375 0.594,0.208 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Engine switch on (IG)


WAVEFORM 26


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.