Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  P010014  Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

HINT:

When DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM calculates the fuel injection duration based on the engine speed and throttle valve angle. Fail-safe mode continues until a pass condition is detected.


A403052C01
5.479,1.854 6.333,2.75 6.333,2.75 6.583,2.75 true 5.917,2.906 6.333,3.417 6.333,3.417 6.583,3.417 true 5.25,2.333 4.917,2.667 4.917,2.667 4.667,2.667 true 2.688,2.083 3.083,2.333 3.083,2.333 3.333,2.333 true 3.063,2 3.25,2.083 3.25,2.083 3.5,2.083 true 2.333,1.333 2.917,1.583 2.917,1.583 3.167,1.583 true 1.417,1.583 1.667,1.583 1.667,1.583 2.094,1.417 true 1.25,2.25 1.5,2.25 1.5,2.25 1.802,2.083 true 4.667,0.583 4.917,0.75 0.25,0.167 10 false *1 6.667,2.677 6.917,2.833 0.25,0.156 10 false *a 4.5,2.583 4.75,2.75 0.25,0.167 10 false *b 3.25,1.51 3.5,1.667 0.25,0.156 10 false *c 1.25,1.5 1.5,1.667 0.25,0.167 10 false *d 3.583,2.01 3.896,2.167 0.313,0.156 10 false *e 3.417,2.26 3.729,2.417 0.313,0.156 10 false *f 1.083,2.167 1.333,2.323 0.25,0.156 10 false *g 6.667,3.344 6.917,3.5 0.25,0.156 10 false *h
*1 Mass Air Flow Meter Sub-assembly - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Air Flow


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery The mass air flow meter sub-assembly output frequency is higher than 9.8 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored SAE Code: P0103
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter sub-assembly output frequency is less than 0.1 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored SAE Code: P0102

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the frequency level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output frequency remains less than 0.1 kHz, or higher than 9.8 kHz for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010012 or P010014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A373493E13
0.313,3.198 0.688,3.427 0.375,0.229 10 false C30 0.625,3.198 2.927,3.458 2.302,0.26 10 false Mass Air Flow Meter Sub-assembly 1.823,2.396 2.281,2.594 0.458,0.198 10 false THA 2.177,2.396 2.333,2.594 0.156,0.198 10 false 4 1.813,1.833 2.271,2.031 0.458,0.198 10 false E2G 2.177,1.844 2.333,2.042 0.156,0.198 10 false 2 1.906,1.229 2.219,1.427 0.313,0.198 10 false FG 2.177,1.229 2.333,1.427 0.156,0.198 10 false 1 1.927,0.646 2.24,0.844 0.313,0.198 10 false 5V 2.167,0.646 2.323,0.844 0.156,0.198 10 false 3 5.177,0.646 5.729,0.927 0.552,0.281 10 false VCVG 4.927,0.635 5.24,0.833 0.313,0.198 10 false 78 5.198,1.219 5.51,1.417 0.313,0.198 10 false VG 4.854,1.219 5.313,1.417 0.458,0.198 10 false 101 5.156,1.823 5.615,2.021 0.458,0.198 10 false E2G 4.875,1.813 5.333,2.01 0.458,0.198 10 false 79 5.188,2.385 5.646,2.583 0.458,0.198 10 false THA 4.875,2.375 5.333,2.573 0.458,0.198 10 false 102 5.438,3.219 5.896,3.417 0.458,0.198 10 false C57 5.76,3.219 6.219,3.417 0.458,0.198 10 false ECM 6.031,1.042 6.188,1.24 0.156,0.198 10 false R 5.833,0.5 6.219,0.698 0.385,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
A373523C07
0.302,1.052 0.656,1.302 0.354,0.25 0.875,1.604 1.292,1.188 true 1.417,1.781 1.573,1.208 true 2.188,1.74 1.802,1.208 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.354,1.094 0.667,1.292 0.313,0.198 10 false C30 0.719,1.615 1.031,1.813 0.313,0.198 10 false FG 1.271,1.802 1.646,2.042 0.375,0.24 10 false E2G 2.135,1.76 2.448,1.958 0.313,0.198 10 false 5V
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C30-3 (5V) - C30-2 (E2G) Engine switch on (IG) 4.8 to 5.2 V
C30-1 (FG) - C30-2 (E2G) Engine switch on (IG) 4.8 to 5.2 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P010012 OR P010014)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P010012 OR P010014)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P010012 or P010014 is output B




A

END

B

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-3 (5V) - C57-78 (VCVG) Always Below 1 Ω
C30-1 (FG) - C57-101 (VG) Always Below 1 Ω
C30-2 (E2G) - C57-79 (E2G) Always Below 1 Ω
C30-3 (5V) or C57-78 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C30-1 (FG) or C57-101 (VG) - Body ground and other terminals Always 10 kΩ or higher
C30-2 (E2G) or C57-79 (E2G) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR