Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P062F44  Internal Control Module EEPROM Data Memory Failure  


DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062F44 Internal Control Module EEPROM Data Memory Failure An ECM internal error (EEPROM) (1 trip detection logic). ECM Comes on DTC stored SAE Code: P062F

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous: Case 1, Case 2
Once per driving cycle: Case 3

TYPICAL ENABLING CONDITIONS

Case 1
All of the following conditions are met -
Fault Code Not stored
OBDII system commands Store
Battery voltage 8 V or higher

Case 2
All of the following conditions are met -
Fault Code Stored
OBDII system commands Clear
Battery voltage 8 V or higher

Case 3
Battery voltage 8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Case 1
The following condition is met 2 data or more
One of the following conditions (a), (b) or (c) is met More than 3 times
(a) EEPROM communication timeout Occurred
(b) Fault Code Not stored
(c) Fault Code Not equal to commanded Fault Code

Case 2
The following condition is met 2 data or more
Either of the following conditions (a) or (b) is met More than 3 times
(a) EEPROM communication timeout Occurred
(b) Fault Code Stored

Case 3
Either of the following conditions is met 1 or 2
1. The following condition is met 2 data or more
EEPROM communication timeout (more than 3 times) Occurred
2. Fault Code data (more than 10 times) Mismatch

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the GTS off.

6.

Turn the engine switch off.

7.

Disconnect the GTS.

8.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

9.

Connect the cable to the negative (-) battery terminal.

10.

Connect the GTS to the DLC3.

11.

Start the engine.

12.

Wait 30 seconds or more.

13.

Turn the GTS on.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes.

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P062F44.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P062F44)
2.READ OUTPUT DTC (DTC P062F44)
a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Connect the GTS to the DLC3.


d.

Start the engine and wait 30 seconds or more.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P062F44 is output B




A

B