Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  P261093  ECM/PCM Engine Off Timer Performance No Operation  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction ECM Comes on DTC stored SAE Code: P2610
P261093 ECM/PCM Engine Off Timer Performance No Operation ECM internal malfunction ECM Comes on DTC stored SAE Code: P2610

DTC No. Monitoring Item Detection Timing Detection Logic
P261029 Soak timer (built into ECM) EVAP monitoring
(engine switch off)
2 trip
P261093 Soak timer (built into ECM) Engine switch on (IG) 2 trip

DESCRIPTION

The soak timer operates after the engine switch is turned off. When a certain amount of time has elapsed after turning the engine switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A404893E08
0.146,1.927 1.135,2.313 0.99,0.385 10 false from Battery 0.625,1.292 1.698,1.49 1.073,0.198 10 false FL MAIN 1.958,1.031 2.719,1.323 0.76,0.292 10 false IG2-MAIN 2.76,1.615 3.531,1.896 0.771,0.281 10 false IG2 NO. 1 1.479,2.031 4.875,2.385 3.396,0.354 10 false from Certification ECU (Smart Key ECU Assembly) 3.74,1.052 4.854,1.333 1.115,0.281 10 false ECU-IG2 NO. 1 4.313,0.729 4.917,1.031 0.604,0.302 10 false IGSW 5,1.125 5.698,1.573 0.698,0.448 10 false Soak Timer IC 4.531,2.896 4.833,3.188 0.302,0.292 10 false +B 5,2.802 5.635,3.271 0.635,0.469 10 false Power Source IC 1.229,3.594 2.396,3.885 1.167,0.292 10 false EFI-MAIN NO. 1 2.646,4.135 3.792,4.438 1.146,0.302 10 false EFI-MAIN NO. 1 4.333,3.708 4.875,3.958 0.542,0.25 10 false MREL 4.99,3.615 5.708,4.083 0.719,0.469 10 false Main Relay Control IC 5.594,4.323 6.052,4.594 0.458,0.271 10 false ECM

MONITOR DESCRIPTION

If the soak timer activates the ECM even though only a short amount of time has elapsed since the engine switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the engine switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the engine switch is turned on (IG).

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

7.

Turn the engine switch off and wait for at least 15 seconds.

8.

Start the engine.

9.

Stop the engine and leave the vehicle for 60 minutes or more.

10.

Turn the engine switch on (IG).

11.

Turn the GTS on.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P261029 or P261093.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P261029 or P261093 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029 OR P261093)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029 OR P261093)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the Pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If no pending DTC is output, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END