81175
1.INSPECT HEADLIGHT UNIT ASSEMBLY LH
| *1 | Headlight Unit Assembly LH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly LH) |
| *c | Component without harness connected
(to Headlight Leveling Motor LH) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH) |
| *e | Component without turn signal light installed
(to Turn Signal Light) |
- | - |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - F-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - F-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - F-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - C-2 | Always | Below 1 Ω |
| B-3 (LOLED0) - C-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (HI+) - E-1 | Always | Below 1 Ω |
| B-1 (HI-) - E-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the headlight fan circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - D-3 | Always | Below 1 Ω |
| B-15 (FANP) - D-2 | Always | Below 1 Ω |
| B-14 (FANG) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - G-1 | Always | Below 1 Ω |
| B-11 (DRL-) - G-3 | Always | Below 1 Ω |
| B-19 (CLL+) - G-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-4 - H-5 | Always | Below 1 Ω |
| G-5 - H-4 | Always | Below 1 Ω |
| G-6 - H-3 | Always | Below 1 Ω |
| G-7 - H-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
81160A
2.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH
| *a | Component without harness connected
(Headlight LED Unit Assembly LH) |
Apply battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly LH.
8116A
3.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit LH) |
Apply battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.
81135
4.INSPECT HEADLIGHT UNIT ASSEMBLY RH
| *1 | Headlight Unit Assembly RH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly RH) |
| *c | Component without harness connected
(to Headlight Leveling Motor RH) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH) |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - F-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - F-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - F-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - C-2 | Always | Below 1 Ω |
| B-3 (LOLED0) - C-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (HI+) - E-1 | Always | Below 1 Ω |
| B-1 (HI-) - E-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the headlight fan circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - D-3 | Always | Below 1 Ω |
| B-15 (FANP) - D-2 | Always | Below 1 Ω |
| B-14 (FANG) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - G-1 | Always | Below 1 Ω |
| B-11 (DRL-) - G-3 | Always | Below 1 Ω |
| B-19 (CLL+) - G-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-4 - H-5 | Always | Below 1 Ω |
| G-5 - H-4 | Always | Below 1 Ω |
| G-6 - H-3 | Always | Below 1 Ω |
| G-7 - H-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
81140
5.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH
| *a | Component without harness connected
(Headlight LED Unit Assembly RH) |
Apply battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly RH.
8112A
6.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit RH) |
Apply battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.