Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.
Do not reuse parts which have reduced fastening ability due to thread damage.
When installing components, make sure that the wire harness is not pinched or pulled.
Do not use solvent to clean components. Only clean them with a dry cloth.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
81102
1.INSTALL HEADLIGHT HOUSING SUB-ASSEMBLY
As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.
Install the 2 vent caps to the headlight housing sub-assembly.
Install the bracket D with the 2 screws to the headlight housing sub-assembly.
Install the bracket C with the 2 screws to the headlight housing sub-assembly.
Engage the guide to temporarily install the headlight leveling motor.
Install the headlight leveling motor with the 3 screws to the headlight housing sub-assembly.
Engage the 3 clamps to install the headlight cord to the headlight housing sub-assembly.
Connect the connector.
|
Engage in this Direction |
Engage the 2 clamps.
Engage the grommet as shown in the illustration.
81160A
2.INSTALL HEADLIGHT LED UNIT ASSEMBLY
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight LED unit assembly or other components.
Prevention of static electricity is required during this procedure.
Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
Do not touch the headlight LED unit assembly with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight LED unit assembly or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
|
Engage in this Direction |
Connect the connector.
Engage the 2 claws as shown in the illustration.
Engage the 3 clamps.
Connect the 2 connectors.
|
Turn in this Direction |
While holding the headlight LED unit assembly by hand, turn the aiming screws as shown in the illustration to install the headlight LED unit assembly.
Turn the aiming screws the same number of times as they were turned during removal.
Engage the pivot collar.
Engage the 2 clamps.
8116A
3.INSTALL NO. 1 HEADLIGHT CLEARANCE LED UNIT
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the No. 1 headlight clearance LED unit or other components.
Prevention of static electricity is required during this procedure.
Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
Do not touch the No. 1 headlight clearance LED unit with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the No. 1 headlight clearance LED unit or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
|
Install in this Direction |
Engage the guide to temporarily install the No. 1 headlight clearance LED unit as shown in the illustration.
Install the No. 1 headlight clearance LED unit with the 2 screws.
Connect the 2 connectors.
81169
4.INSTALL HEADLIGHT REFLECTOR
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight reflector or other components.
Do not touch the headlight reflector with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight reflector or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
|
Install in this Direction |
Engage the 2 guides to temporarily install the headlight reflector as shown in the illustration.
Install the headlight reflector with the screw.
81132B
5.INSTALL HEADLIGHT LENS GASKET
The headlight lens gasket must not be reused.
Make sure to wear clean rubber gloves when performing this procedure.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Completely remove the old headlight lens gasket.
|
Cleaning Area |
Clean the installation groove of the headlight lens.
| *a | Release Paper |
| *b | Tape |
| *c | 90° |
Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.
Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.
Using scissors, cut the end of the headlight lens gasket at a 90° angle.
|
Starting Position |
Starting from the position shown in the illustration and moving counterclockwise, temporarily install the headlight lens gasket as shown in the illustration.
Gently install the headlight lens gasket without pulling it.
|
Corner Groove |
Set the headlight lens gasket into the corner groove.
Gently install the headlight lens gasket without pulling it.
If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.
|
Press in this Direction |
|
Release Paper |
Using 2 screwdrivers with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.
Gently install the headlight lens gasket without pulling it.
If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.
|
Corner Groove |
Repeat the following until the headlight lens gasket reaches the starting position: Temporarily install the headlight lens gasket to the straight groove and completely press it into the groove, and then temporarily install it to the corner groove and completely press it into the groove.
Using scissors, cut the headlight lens gasket at a 45° angle at the starting position so that the headlight lens gasket overlaps itself 20 mm (0.7874 in.).
| Area | Dimension |
|---|---|
| A | 20 mm (0.7874 in.) |
Check the installation condition of the headlight lens gasket.
Make sure the headlight lens gasket is not protruding and is installed properly.
Make sure there is no gap between the ends of the headlight lens gasket.
Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.
81171B
6.INSTALL HEADLIGHT LENS
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight lens.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Clean the sealing surface of the headlight lens.
Temporarily install the headlight lens to the headlight housing sub-assembly.
|
Headlight Lens Gasket |
|
Headlight Housing Sub-assembly |
|
Headlight Lens |
Temporarily install the headlight lens in the middle of the headlight lens gasket as shown in the illustration.
Check that the entire circumference of the headlight lens is positioned above the middle of the headlight lens gasket.
Engage the 9 claws to install the headlight lens to the headlight housing sub-assembly.
Make sure all of the claws are engaged.
Install the 8 screws.
Check the installation condition of the headlight lens gasket.
Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.
81510C
7.INSTALL FRONT TURN SIGNAL LIGHT BULB
Install the front turn signal light bulb to the headlight cord.
|
Install in this Direction |
Turn the headlight cord with the front turn signal light bulb as shown in the illustration to install them as a unit.
81134
8.INSTALL HEADLIGHT GASKET
81056A
9.INSTALL HEADLIGHT ECU SUB-ASSEMBLY