While torque sensor system, motor system or ECU system malfunctions are detected, the fail-safe function suspends power assist. However, power assist continues with limited assistance amount if only C1533 or C1534 is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1511 | Torque Sensor1 | Torque sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1512 | Torque Sensor2 | Torque sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1513 | Torque Sensor Deviation Excessive | Torque sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1514 | Torque Sensor Power Supply Voltage | Torque sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1521 | Short in Motor Circuit | Motor overcurrent | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1522 | Power Supply Sensor | Motor current sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1523 | Current Deviation Excessive | Excessively large current deviation | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1528 | Motor Rotation Angle Sensor | Motor rotation angle sensor malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1531 | ECU Malfunction | ECU internal malfunction (CPU malfunction) | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1532 | ECU Malfunction | ECU internal malfunction (Peripheral circuit malfunction) | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1533 | Temperature Sensor Circuit is Low or High | ECU internal malfunction (Substrate temperature sensor malfunction) | Rack and pinion power steering gear assembly | EPS warning light: Comes on | The ECU judges the system has returned to normal | - |
| C1534 | EEPROM | ECU internal malfunction (EEPROM error) | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
| C1555 | Motor Relay Welding Failure | Motor relay circuit malfunction | Rack and pinion power steering gear assembly | EPS warning light: Comes on | Ignition switch is turned to ON again | - |
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs other than C1511, C1512, C1513, C1514, C1521, C1522, C1523, C1528, C1531, C1532, C1533, C1534 or C1555 are not output. | A |
| DTCs other than C1511, C1512, C1513, C1514, C1521, C1522, C1523, C1528, C1531, C1532, C1533, C1534 or C1555 are output. | B |
| DTCs are not output. | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING