Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM33A0E _55 Steering _065370 POWER ASSIST SYSTEMS _0327166 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552  PIG Power Supply Voltage  C1554  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the PIG power source and power supply relay system, the fail-safe function works to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1552 PIG Power Supply Voltage PIG power source circuit malfunction
·

EPS fuse

·

Harness or connector

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on Ignition switch is turned to ON again -
C1554 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

Harness or connector

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on Ignition switch is turned to ON again -

WIRING DIAGRAM

C375258E03
1.958,0.698 3,0.917 1.042,0.219 10 false from Battery 4.219,0.875 4.875,1.094 0.656,0.219 10 false EPS 5.052,0.615 5.667,0.833 0.615,0.219 10 false 8 5.688,0.708 6.302,0.927 0.615,0.219 10 false PIG 5.677,1.427 6.292,1.646 0.615,0.219 10 false PGND 5.052,1.333 5.667,1.552 0.615,0.219 10 false 7 5.167,2.583 5.865,2.802 0.698,0.219 10 false C71 5.167,2.75 6.667,3.25 1.5,0.5 10 false Rack and Pinion Power Steering Gear Assembly 5.271,2.052 6.615,2.313 1.344,0.26 10 false Power Steering ECU

CAUTION / NOTICE / HINT

NOTICE:
·

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RACK AND PINION POWER STEERING GEAR ASSEMBLY - BODY GROUND)
a.

Disconnect the C71 rack and pinion power steering gear assembly connector.

C374510C02
1.958,0.271 2.375,0.521 0.417,0.25 3.938,1.198 4.604,1.5 false 2.583,1.469 3.208,1.208 false 2.031,0.313 2.5,0.573 0.469,0.26 10 false C71 2.146,1.406 2.615,1.667 0.469,0.26 10 false PGND 4.698,1.438 5.167,1.698 0.469,0.26 10 false PIG 0.188,0.125 0.656,0.385 0.469,0.26 10 false *a
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C71-8 (PIG) - Body ground Ignition switch ON 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C71-7 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR