Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM33A0E _55 Steering _065370 POWER ASSIST SYSTEMS _0327166 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

Perform the following troubleshooting procedure when the EPS warning light remains on after the engine is started, but no DTCs are stored.

HINT:
·

If the power steering ECU (rack and pinion power steering gear assembly) detects a malfunction in the power source voltage input (IG) circuit, the EPS warning light illuminates.

·

If the power steering ECU (rack and pinion power steering gear assembly) detects a drop in the power voltage input (IG and PIG) circuit, the force required to turn the steering wheel may increase, the EPS warning light turns on in order to warn the driver.



WIRING DIAGRAM

C375259E02
1.469,1.635 2.917,1.875 1.448,0.24 10 false from IG1-NO. 1 Relay 2.01,2.229 3.042,2.49 1.031,0.26 10 false from Battery 0.833,1.083 1.333,1.292 0.5,0.208 10 false K21 0.833,1.25 2.792,1.615 1.958,0.365 10 false Combination Meter Assembly 1.719,0.51 2.219,0.729 0.5,0.219 10 false CANH 2.229,0.74 2.594,0.979 0.365,0.24 10 false 31 2.208,0.333 2.573,0.573 0.365,0.24 10 false 32 4.969,0.344 5.333,0.583 0.365,0.24 10 false 10 4.969,0.75 5.333,0.99 0.365,0.24 10 false 11 5.021,1.542 5.385,1.781 0.365,0.24 10 false 4 5.021,2.156 5.385,2.396 0.365,0.24 10 false 8 5.021,2.625 5.385,2.865 0.365,0.24 10 false 7 4.833,3.958 5.167,4.208 0.333,0.25 10 false C71 5.167,3.958 6.667,4.708 1.5,0.75 10 false Rack and Pinion Power Steering Gear Assembly 5.625,2.74 6.177,2.99 0.552,0.25 10 false PGND 5.615,2.25 5.979,2.49 0.365,0.24 10 false PIG 4.104,1.781 4.844,2.01 0.74,0.229 10 false EPS-IG1 0.802,4.333 2.792,4.719 1.99,0.385 10 false : CAN Communication Line 4.229,2.396 4.969,2.625 0.74,0.229 10 false EPS 1.74,0.906 2.24,1.125 0.5,0.219 10 false CANL 5.604,0.5 6.104,0.719 0.5,0.219 10 false CANH 5.615,0.917 6.115,1.135 0.5,0.219 10 false CANL 5.615,1.625 5.979,1.865 0.365,0.24 10 false IG 5.25,3.323 6.604,3.542 1.354,0.219 10 false Power Steering ECU

CAUTION / NOTICE / HINT

NOTICE:
·

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ASSIST LIMIT RECORD
a.

Using the GTS, read the Data List item "Assist Limit Record 1".

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Assist Limit Record 1 Information of assist limit that was used in the past or is currently in use (latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Chassis > EMPS > Data List
Tester Display
Assist Limit Record 1
50003 142 73
HINT:

For the Data List item "Assist Limit Record 1", each item in the Range is described below.

Range Description
Mtr Overheat When the vehicle is stopped or traveling at low speed, and steering operations are performed repeatedly or the steering wheel is turned all the way to the side and held there for a long time, assist may be limited in order to prevent overheating of the power steering motor assembly and power steering ECU assembly.
After 10 minutes elapse with the engine stopped and no steering operations being performed, the system will return to normal.
After recovering from the overheated condition, assist can be performed as usual.
Pow Vol Low When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be stopped.
After the battery condition returns to normal, assist can be performed as usual.
Pow Vol Low Prevent When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.
Eng Stall When the engine stalls, battery charge becomes insufficient, so assist is stopped.
After recovering from the engine stall, assist can be performed as usual.
Ready OFF After Ready ON, if a malfunction in the HV system etc. causes a return to Ready OFF, the HV battery charge becomes insufficient, so assist is stopped.
After returning to Ready ON state, assist can be performed as usual.
Mtr Overload When the steering wheel cannot turn, such as when a road wheel is against a curb, if the driver continues to apply force to the steering wheel, current to the motor may be limited to prevent overheating.
When the steering wheel is returned to a neutral position, assist can be performed as usual.
DC-DC Malf If there is a malfunction in the DC-DC converter, etc., assist may be limited.
After the DC-DC converter returns to normal, assist can be performed as usual.
Vhcl Spd Sig Malf If the vehicle speed signal is abnormal due to a wheel speed sensor malfunction, etc., assist may be limited.
Batt Vol Keep When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.



b.

Based on the "Assist Limit Record 1" information, the following Data List items and the information from the customer interview, explain the situation to the customer.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Record 1 Key Cycle Number of times that the ignition switch was turned to ON before Assist Limit Record 1 was stored Min.: 0 times
Max.: 65535 times
- -
Record 1 Key Cycle Elapsed Time Period of time that elapsed since the ignition switch was turned to ON before Assist Limit Record 1 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Chassis > EMPS > Data List
Tester Display
Record 1 Key Cycle
Record 1 Key Cycle Elapsed Time
50003 142 74,75
Result:
Result Proceed to
"Unrec" is displayed A
Other than Unrec is displayed B


HINT:

If it is necessary to investigate further into the past, check the "Assist Limit Record 2" and "Assist Limit Record 3" information in the same way as "Assist Limit Record 1".




A

2.CHECK HARNESS AND CONNECTOR

B

EXPLAIN THE CHECKED "ASSIST LIMIT RECORD 1" TO THE CUSTOMER, CROSS-CHECKING THE DATA LIST ITEMS WITH THE INFORMATION FROM THE CUSTOMER INTERVIEW.

2.CHECK HARNESS AND CONNECTOR
a.

Jiggle the rack and pinion power steering gear assembly connectors and wire harness up and down, and left and right to check the illumination condition of the EPS warning light in the combination meter assembly.

OK:

The EPS warning light illumination condition does not change.


HINT:

When the EPS warning light is operating properly, it illuminates when the ignition switch is turned to ON and turns off when the engine is started.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

4.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)

B

4.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)
a.

Disconnect the C71 rack and pinion power steering gear assembly connector.


C374510C10
1.948,0.229 2.365,0.479 0.417,0.25 3.448,1.135 2.583,0.729 false 2.583,1.469 3.208,1.208 false 3.969,1.198 4.635,1.479 false 2.031,0.271 2.5,0.531 0.469,0.26 10 false C71 2.146,1.406 2.615,1.667 0.469,0.26 10 false PGND 2.385,0.646 2.854,0.906 0.469,0.26 10 false IG 0.125,0.094 0.594,0.354 0.469,0.26 10 false *a 4.708,1.427 5.177,1.688 0.469,0.26 10 false PIG
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C71-4 (IG) - Body ground Ignition switch ON 8 to 16 V
C71-8 (PIG) - Body ground Ignition switch ON 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C71-7 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the C71 rack and pinion power steering gear assembly connectors.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
EPS Warning
50004 409 128

c.

Check the combination meter assembly.

OK:

The EPS warning light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG