Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065369 PARKING BRAKE _0328504 ELECTRIC PARKING BRAKE SYSTEM U

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Brake Warning Light Brake warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Gear Position Gear position information "P,N", R, 1st-8th, Fail or Not R Actual gear position -
Shift Lever Position Shift lever position information "P,N", R, D/M, 1st-6th/B or Fail Actual shift lever position -
Shift Information Shift information ON or OFF ON: During gear change
OFF: Not during gear change
-
Deceleration Sensor Acceleration sensor reading Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor 2 reading Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF ON: Relay on
OFF: Relay off
-
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
Stop Light Relay Output Stop light control relay (Stop light switch assembly) output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-
EFI Communication Open ECM communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
Number of DTC Number of DTC recorded Min.: 0, Max.: 255 - -
IG Voltage Value Decreased +BS voltage value decrease detection Error or Normal Error: Voltage low
Normal: Normal
-
IG Voltage Value Increased +BS voltage value increase detection Error or Normal Error: Voltage high
Normal: Normal
-
Vehicle Speed (Control Value) Vehicle speed
(control value)
Min.: 0.0 km/h (0.0 MPH)
Max.: 326.4 km/h (202.8 MPH)
- -
ECU +B1 Voltage Skid control ECU
(brake actuator assembly) +B1 voltage
0.00 to 20.00 V 11 to 14 V -
RH Actuator Motor Input Voltage Parking brake motor RH (parking brake actuator assembly RH) input voltage 0.00 to 20.00 V - -
RH Actuator Motor +Terminal Voltage Parking brake motor RH (parking brake actuator assembly RH) positive (+) terminal side voltage 0.00 to 20.00 V - -
RH Actuator Motor -Terminal Voltage Parking brake motor RH (parking brake actuator assembly RH) negative (-) terminal side voltage 0.00 to 20.00 V - -
LH Actuator Motor Input Voltage Parking brake motor LH (parking brake actuator assembly LH) input voltage 0.00 to 20.00 V - -
LH Actuator Motor +Terminal Voltage Parking brake motor LH (parking brake actuator assembly LH) positive (+) terminal side voltage 0.00 to 20.00 V - -
LH Actuator Motor -Terminal Voltage Parking brake motor LH (parking brake actuator assembly LH) negative (-) terminal side voltage 0.00 to 20.00 V - -
Indoor Temperature Interior temperature -6.50 to 57.25°C (20.30 to 135.00°F) - When displayed value differs from actual interior temperature, air conditioning system and CAN communication system may be malfunctioning
Ambient Temperature Ambient temperature -40 to 50°C (-40 to 122°F) - When displayed value differs from actual ambient temperature, air conditioning system and CAN communication system may be malfunctioning
EPB Switch Electric parking brake switch (electric parking brake switch assembly) input OFF, Lock, Release or Unknown OFF: Lock switch and release switch are off
Lock: Lock switch on Release: Release switch on
When not normal, electric parking brake switch (electric parking brake switch assembly) release side system may be malfunctioning
HINT:

EPB stands for electric parking brake.


Auto Mode Request Auto mode request status OFF or ON - -
Shift Position Position of shift lever P, N, R, D or Unknown P: Shift lever in P
N: Shift lever in N
R: Shift lever in R
D: Shift lever in D or M
-
IG Switch IG power source status OFF or ON OFF: IG power source voltage is not input to skid control ECU (brake actuator assembly)
ON: IG power source voltage is input to skid control ECU (brake actuator assembly)
-
Brake Hold Ready Brake hold control permission status OFF or ON - -
Brake Hold Control Mode Brake hold control mode OFF, ON, Release or EPB OFF: Brake hold control is not operating
ON: Brake hold control is operating
Release: Brake hold control is released
EPB: Parking brake is locked during brake hold control
HINT:

EPB stands for electric parking brake.


RH Actuator Current Status Parking brake actuator assembly RH monitoring current condition Inval or Valid Valid -
LH Actuator Current Status Parking brake actuator assembly LH monitoring current condition Inval or Valid Valid -
RH Actuator Nut Stroke Parking brake actuator assembly RH nut stroke value 0.000 to 8.160 mm (0.000 to 0.321 in.) - -
LH Actuator Nut Stroke Parking brake actuator assembly LH nut stroke value 0.000 to 8.160 mm (0.000 to 0.321 in.) - -
RH Actuator Motor Actual Current Parking brake motor RH (parking brake actuator assembly RH) current value -5.0362 to 50.5000 A - -
RH Actuator 0 load Current Parking brake actuator assembly RH current value with no load -5.0362 to 50.5000 A - -
LH Actuator Motor Actual Current Parking brake motor LH (parking brake actuator assembly LH) current value -5.0362 to 50.5000 A - -
LH Actuator 0 load Current Parking brake actuator assembly LH current value with no load -5.0362 to 50.5000 A - -
Counter of IG ON After EPB Control Cancel Number of times the ignition switch was turned ON after EPB control was canceled 0 to 255 Times - -
RH Actuator Status Parking brake actuator assembly RH condition Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control - -
LH Actuator Status Parking brake actuator assembly LH condition Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control - -
Auto Mode AUTO (shift-linked) mode permission status OFF or ON OFF: Manual mode.
ON: AUTO (shift-linked) mode
-
Dynamic PKB Mode Dynamic parking brake operation status OFF or ON OFF: Dynamic parking brake is not operating
ON: Dynamic parking brake is operating
-
Permission of Interlocking Shift AUTO (shift-linked) mode permission status OK or NG - -
Permission of Interlocking Brake Brake-linked permission status OK or NG - -
Permission of RH Interlocking PKB Lock Parking brake actuator assembly RH parking brake lock control permission status OK or NG OK -
Permission of RH Interlocking PKB Release Parking brake actuator assembly RH parking brake release control permission status OK or NG - -
Permission of RH Interlocking Dynamic PKB Parking brake actuator assembly RH dynamic parking control permission status OK or NG - -
Permission of RH Interlocking PKB Full Release Parking brake actuator assembly RH parking brake full release permission status OK or NG - -
Permission of LH Interlocking PKB Lock Parking brake actuator assembly LH parking brake lock control permission status OK or NG OK -
Permission of LH Interlocking PKB Release Parking brake actuator assembly LH parking brake release control permission status OK or NG - -
Permission of LH Interlocking Dynamic PKB Parking brake actuator assembly LH dynamic parking control permission status OK or NG - -
Permission of LH Interlocking PKB Full Release Parking brake actuator assembly LH parking brake full release permission status OK or NG - -
Fade Status Fade status OFF or ON - -
EPB Control Cancel History Cause of EPB control cancel No Recoded, RH IC Overheat, LH IC Overheat, RH Actuator Motor Current High, LH Actuator Motor Current High, RH Actuator Motor +B Open Judging, LH Actuator Motor +B Open Judging, IG Voltage High/Low -
HINT:

EPB stands for electric parking brake.


Parking Brake Light Parking brake indicator light (red) output signal OFF, Light or Blink OFF: Parking brake indicator light (red) turns off
Light: Parking brake indicator light (red) illuminates
Blink: Parking brake indicator light (red) flashes
-
EPB Warning Light Brake system warning light (yellow indicator) output signal OFF or ON OFF: Brake system warning light (yellow indicator) turns off
ON: Brake system warning light (yellow indicator) illuminates
-


PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.


f.

According to the display on the GTS, perform the Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Auto Mode AUTO (shift-linked) mode ON or OFF
·

Vehicle stopped

·

Ignition switch ON


EPB Warning Light Brake system warning light (yellow) ON or OFF
·

Vehicle stopped

·

Ignition switch ON


HINT:

EPB stands for electric parking brake.


PKB Light Parking brake indicator light (red) ON or OFF
·

Vehicle stopped

·

Ignition switch ON


PKB Lock Control Parking brake lock control ON or OFF
·

Vehicle stopped

·

Ignition switch ON


PKB Release Control Parking brake release control ON or OFF
·

Vehicle stopped

·

Ignition switch ON


PKB Full Release Control Parking brake full release control ON or OFF
·

Vehicle stopped

·

Ignition switch ON