Home › Engine / Hybrid System › A25A-FKS (INTAKE / EXHAUST) › EXHAUST PIPE › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065345 A25A-FKS INTAKE / EXHAUST _0328577 EXHAUST PIPE A

A25A-FKS INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly (TWC: Rear Catalyst), center exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A412413

Remove the 2 bolts and disconnect the tail exhaust pipe assembly from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 17420 2.REMOVE CENTER EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402249

Remove the 2 bolts and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Remove the center exhaust pipe assembly from the exhaust pipe support.


c.

Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 58166A 3.REMOVE FRONT FLOOR COVER LH

a.
A402250N01
2.177,0.052 2.333,0.25 0.156,0.198 10 true A 1.698,0.458 1.854,0.656 0.156,0.198 10 true A 1.448,0.969 1.604,1.167 0.156,0.198 10 true A 2.031,1.708 2.188,1.885 0.156,0.177 10 true C 2.823,0.781 2.979,0.958 0.156,0.177 10 true C 2.49,1.094 2.646,1.271 0.156,0.177 10 true C 0.958,0.813 1.115,0.99 0.156,0.177 10 true C 0.75,1.302 0.906,1.479 0.156,0.177 10 true C 1.167,0.083 1.323,0.26 0.156,0.177 10 true C 0.573,1.688 0.729,1.865 0.156,0.177 10 true B 2.438,1.521 2.594,1.719 0.156,0.198 10 true A

Remove the 3 bolts and 4 clips (A).


b.

Disengage the grommet (B) and 6 clips (C) to remove the front floor cover LH.


Hide 58165C 4.REMOVE FRONT FLOOR COVER RH

a.
A402251N01
0.333,1.01 0.49,1.208 0.156,0.198 10 true A 1.885,0.51 2.031,0.677 0.146,0.167 10 true A 1.656,0.385 1.802,0.552 0.146,0.167 10 true A 1.26,0.906 1.406,1.073 0.146,0.167 10 true A 3.01,0.365 3.156,0.531 0.146,0.167 10 true C 2.604,0.917 2.75,1.083 0.146,0.167 10 true C 2.104,1.427 2.25,1.594 0.146,0.167 10 true C 1.719,1.854 1.865,2.021 0.146,0.167 10 true B 1.063,0.125 1.208,0.292 0.146,0.167 10 true C 0.948,0.521 1.094,0.688 0.146,0.167 10 true C 0.219,1.594 0.365,1.76 0.146,0.167 10 true C

Remove the 3 bolts and 4 clips (A).


b.

Disengage the grommet (B) and 6 clips (C) to remove the front floor cover RH.


Hide 57533B 5.REMOVE FRONT CENTER FLOOR BRACE

a.
A402252

Remove the 4 bolts and front center floor brace from the vehicle body.


Hide 57523A 6.REMOVE CENTER FLOOR CROSSMEMBER BRACE

a.
A402253

Remove the 4 bolts and center floor crossmember brace from the vehicle body.


Hide 89467C 7.REMOVE AIR FUEL RATIO SENSOR (for Sensor 2)

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402254

Remove the 2 nuts and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst).


b.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


c.

Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 17408 9.REMOVE TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.



a.
A408269

Remove the tail exhaust pipe baffle sub-assembly.