Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › THROTTLE BODY › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328589 THROTTLE BODY A

A25A-FKS ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A415428

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 2 wire harness clamps.


c.
A402353C01
0.594,1.708 0.708,1.135 0.708,1.135 0.875,1.135 true 0.979,3.219 0.979,3.021 0.979,3.021 1.188,2.729 true 1.583,3.146 1.813,3.344 0.229,0.198 10 true *a 1.469,0.656 1.708,0.854 0.24,0.198 10 true *b 2.01,1.167 2.25,1.365 0.24,0.198 10 true *b 2.552,2.938 2.781,3.135 0.229,0.198 10 true *a 0.917,3.229 1.156,3.427 0.24,0.198 10 true *1 0.917,1.052 1.219,1.302 0.302,0.25 10 false *2 0.469,3.604 0.698,3.802 0.229,0.198 10 false *c 1.375,3.604 1.604,3.802 0.229,0.198 10 false *d
*1 Vacuum Hose
*2 No. 2 Ventilation Hose
*a Air Cleaner Cap Clamp
*b Guide
*c Unlocked
*d Locked


Disconnect the vacuum hose from the air cleaner hose.


d.

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


e.

Disengage the 2 air cleaner cap clamps.


f.

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


g.

Lock the hose clip and remove the air cleaner cap with air cleaner hose from the throttle body with motor assembly.


Hide 22030 4.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A402356

Disconnect the throttle body with motor assembly connector.


b.

Slide the clip and disconnect the No. 6 water by-pass hose from the throttle body with motor assembly.


c.

Using an 8 mm socket wrench, remove the 3 bolts and separate the throttle body with motor assembly from the intake manifold.


d.
A402358

Slide the clip and disconnect the No. 5 water by-pass hose to remove the throttle body with motor assembly.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



Hide 22271 5.REMOVE THROTTLE BODY GASKET

a.
A402360

Remove the throttle body gasket from the intake manifold.