Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › RELAY
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328604 RELAY G

A25A-FKS ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89561B 1.INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 1)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 electronic fuel injection main relay (EFI-MAIN NO. 1).


Hide 89561C 2.INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 2)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 electronic fuel injection main relay (EFI-MAIN NO. 2).


Hide 89561E 3.INSPECT NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 3)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 3 electronic fuel injection main relay (EFI-MAIN NO. 3).


Hide 85910Z 4.INSPECT EFI INJECTION RELAY (D INJ)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the EFI injector relay (D INJ).


Hide 85912K 5.INSPECT VVT RELAY (VVT)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the VVT relay (VVT).


Hide 28371C 6.INSPECT NO. 2 IGNITION RELAY (IG2 NO. 1)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 ignition relay (IG2 NO. 1).