Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065385 SEAT _0328609 SEAT HEATER SYSTEM U

SEAT  SEAT HEATER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


B416357N18
1.167,0.25 1.583,0.5 0.417,0.25 2.833,0.25 3.25,0.5 0.417,0.25 4.583,0.25 5,0.5 0.417,0.25 6.146,0.083 6.563,0.333 0.417,0.25 4.656,0.292 5.115,0.49 0.458,0.198 10 false K54 2.917,0.292 3.375,0.49 0.458,0.198 10 false K55 1.26,0.281 1.719,0.479 0.458,0.198 10 false K56 6.281,0.125 6.74,0.323 0.458,0.198 10 false z8

a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K54-2 (IG+) - Body ground LA-GR - Body ground IG power supply Engine switch on (IG) 11 to 14 V
K54-2 (IG+) - Body ground LA-GR - Body ground IG power supply Engine switch off Below 1 V
K54-4 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K54 air conditioning amplifier assembly connector.


d.

Measure the voltage and check for pulses generation according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K56-16 (SHP+) - K54-4 (GND) LG - W-B Refreshing seat switch volume signal
·

Engine switch on (IG)

·

Refreshing seat switch on (LO)

(heater position)


Below 1 V
K56-15 (SHD+) - K54-4 (GND) BE - W-B Refreshing seat switch volume signal
·

Engine switch on (IG)

·

Refreshing seat switch on (LO)

(heater position)


Below 1 V
K54-14 (LIN1) - Body ground BE - Body ground Refreshing seat switch signal Engine switch on (IG) Pulse generation



CHECK REFRESHING SEAT SWITCH


B454542N02
3.333,0.167 3.75,0.417 0.417,0.25 3.417,0.208 3.875,0.406 0.458,0.198 10 false K49

a.

Disconnect the K49 refreshing seat switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K49-1 (IG) - Body ground LG - Body ground IG power supply Engine switch on (IG) 11 to 14 V
K49-1 (IG) - Body ground LG- Body ground IG power supply Engine switch off Below 1 V
K49-5 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K49 refreshing seat switch connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K49-3 (SLIN) - Body ground B - Body ground Refreshing seat switch signal Engine switch on (IG) Pulse generation