Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328640 EXHAUST MANIFOLD A

2AR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 25586 1.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 4 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25051 3.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold converter sub-assembly (TWC: Front Catalyst) to the cylinder head sub-assembly with the 5 nuts.


c.

Temporarily install the No. 2 manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.


d.

Temporarily install the manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.


e.
A407109N01
0.604,0.219 0.76,0.406 0.156,0.188 10 true 2 0.135,1.385 0.292,1.573 0.156,0.188 10 true 4 1.969,1.354 2.146,1.563 0.177,0.208 10 true 1 3.208,1.396 3.385,1.604 0.177,0.208 10 true 5 2.896,0.188 3.073,0.396 0.177,0.208 10 true 3

Tighten the 5 nuts in the order shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 17167 5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17118 6.INSTALL MANIFOLD STAY

a.
A407106N01
0.854,1.427 1.031,1.635 0.177,0.208 10 true 1 2.188,1.604 2.365,1.813 0.177,0.208 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17139 7.INSTALL NO. 2 MANIFOLD STAY

a.
A415478

Tighten the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
A407113C01
2.333,0.948 2.552,1.146 0.219,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, tighten the nut.

Torque:
Specified tightening torque : 43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.8 N*m (385 kgf*cm, 28 ft.*lbf)




Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install 2 new gaskets to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A415472C01
2.302,0.813 2.521,0.229 2.521,0.229 2.875,0.229 true 0.677,1.49 0.677,1.146 0.677,1.146 0.969,0.927 false 0.531,0.24 0.708,0.24 0.708,0.24 0.969,0.667 false 0.375,0.177 0.635,0.375 0.26,0.198 10 false *1 0.625,1.531 0.938,1.688 0.313,0.156 10 false *2 2.906,0.188 3.146,0.375 0.24,0.188 10 false *3 0.271,1.5 0.583,1.656 0.313,0.156 10 false *a
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Center Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and center exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Connect the heated oxygen sensor connector.


Hide 57523A 10.INSTALL CENTER FLOOR CROSSMEMBER BRACE

Hide 57533B 11.INSTALL FRONT CENTER FLOOR BRACE