Home › Engine / Hybrid System › 2GR-FKS (STARTING) › STARTER
RM33A0E _51 Engine / Hybrid System _065339 2GR-FKS STARTING _0328805 STARTER G

2GR-FKS STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A406903C01
1.604,2.177 1.604,1.885 false 2.198,2.125 2.594,1.281 true 2.833,1.198 3.083,0.677 true 2.104,2.125 2.417,2.281 0.313,0.156 10 false *a 3.094,0.552 3.406,0.708 0.313,0.156 10 false *b 1.531,2.177 1.844,2.333 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Moves outward


Connect a battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



b.

Perform a hold-in test.

i.
A406904C01
2.823,1.208 3.094,0.719 true 2.188,2.052 2.646,1.25 true 1.594,2.271 1.594,1.875 false 2.073,2.031 2.385,2.188 0.313,0.156 10 false *a 3.104,0.604 3.417,0.76 0.313,0.156 10 false *b 1.521,2.281 1.833,2.438 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.

Perform a return test.

i.
A406905C01
2.802,1.25 3.094,0.75 true 2.063,2.208 2.583,1.333 true 1.594,2.333 1.594,1.938 false 1.979,2.219 2.292,2.375 0.313,0.156 10 false *a 3.104,0.646 3.417,0.802 0.313,0.156 10 false *b 1.531,2.354 1.844,2.51 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect
V100136

Returns inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform a no-load performance test.

i.

Connect the field coil lead wire to terminal C with the nut. Make sure that the field coil lead wire is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A406906C01
2.854,2.313 2.854,1.01 true 1.531,2.156 1.531,1.833 false 2.094,2.042 2.521,1.198 true 1.99,2.042 2.302,2.198 0.313,0.156 10 false *a 2.781,2.333 3.094,2.49 0.313,0.156 10 false *b 1.458,2.167 1.771,2.323 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal 30
*c Starter Body
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

HINT:

If there is no continuity between any segments, replace the starter armature assembly.


a.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (400-grit) or on a lathe.


b.
A082643C13
2.833,1.01 2.594,1.01 2.594,1.01 1.927,1.344 false 2.875,0.906 3.188,1.063 0.313,0.156 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A082644C12
1.458,1.76 1.604,1.76 1.604,1.76 1.99,1.375 false 0.573,1.427 0.76,1.427 0.76,1.427 1.219,1.073 false 1.313,1.646 1.625,1.802 0.313,0.156 10 false *a 0.406,1.323 0.719,1.479 0.313,0.156 10 false *b
*a Segment
*b Starter Armature Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A206798C12
1.021,0.823 0.688,0.344 0.688,0.344 0.448,0.344 false 2.635,1.896 2.448,1.896 2.448,1.896 1.99,1.354 false 0.281,0.24 0.594,0.396 0.313,0.156 10 false *a 2.677,1.781 2.99,1.938 0.313,0.156 10 false *a
*a Armature Shaft


Check the commutator for runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the runout.

Maximum Runout:

0.05 mm (0.00197 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A062221

Using a vernier caliper, measure the commutator diameter.

Standard Diameter:

29 mm (1.14 in.)


Minimum Diameter:

28 mm (1.10 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A302776

Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard Undercut Depth:

0.7 mm (0.0276 in.)


Minimum Undercut Depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the brush length.

i.
A215975C01
2.74,0.375 3.052,0.531 0.313,0.156 10 false *a
*a Brush Length


Using a vernier caliper, measure the brush length.

Standard Length:

14.4 mm (0.567 in.)


Minimum Length:

9.0 mm (0.354 in.)


If the brush length is less than the minimum, replace the starter brush holder assembly.



b.
A095705N11
0.406,1.146 1.01,1.146 false 0.677,2.021 0.875,2.021 0.875,2.021 1.385,1.792 false 2.135,0.521 2.406,0.156 2.406,0.156 2.563,0.156 false 2.5,1.146 2.938,1.146 false 0.271,1.042 0.427,1.24 0.156,0.198 10 false A 0.552,1.927 0.708,2.125 0.156,0.198 10 false B 2.604,0.063 2.76,0.26 0.156,0.198 10 false D 2.99,1.042 3.146,1.24 0.156,0.198 10 false C

Check the brush holder resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
A - C
B - D
C - D
Always 10 kΩ or higher
A - D
B - C
Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



Hide 4.INSPECT STARTER CLUTCH

A406907C01
0,0 0,0 false
V100136

Lock
V100135

Free


a.

Check the clutch pinion gear.

i.

Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If the clutch pinion gear does not operate as specified, replace the repair service starter kit.



Hide 28150 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A082640

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If the plunger does not operate as specified, replace the magnet starter switch assembly.



b.
A194284C12
1.906,0.771 2.125,0.542 2.125,0.542 2.208,0.542 false 1.563,1.198 1.344,1.594 1.344,1.594 1.24,1.594 true 2.271,0.427 2.583,0.583 0.313,0.156 10 false *a 1.073,1.49 1.385,1.646 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A194285C12
1.375,0.75 1.646,0.385 1.646,0.385 1.844,0.385 false 2.01,1.208 2.229,1.063 2.229,1.063 2.406,1.063 false 2.448,0.958 2.76,1.115 0.313,0.156 10 false *a 1.906,0.292 2.219,0.448 0.313,0.156 10 false *b
*a Terminal 50
*b Magnet Starter Switch Assembly Body


Check the holding coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 -Magnet starter switch assembly body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.