Home › Engine / Hybrid System › 2AR-FE (STARTING) › STARTER › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065330 2AR-FE STARTING _0328809 STARTER A

2AR-FE STARTING  STARTER  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

A187220

a.

Remove the nut and disconnect the field coil lead wire from the magnet starter switch assembly.


b.
A201461

While holding the magnet starter switch assembly to the repair service starter kit, remove the 2 nuts.


c.
A269260C01
1.323,0.479 1.458,0.135 1.458,0.135 1.594,0.135 true 1.698,0.51 1.833,0.167 1.833,0.167 1.969,0.167 true 2.198,0.469 2.458,0.281 2.458,0.281 2.604,0.281 false 2.625,0.188 2.938,0.344 0.313,0.156 10 false *1 1.604,0.052 1.917,0.208 0.313,0.156 10 false *a 1.979,0.083 2.292,0.24 0.313,0.156 10 false *b
*1 Magnet Starter Switch Assembly
*a Pinion Drive Lever
*b Hook


While lifting the rear of the magnet starter switch assembly, remove the hook from the pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
A187222C01
0.333,0.979 0.51,0.979 false 1.813,1.771 2.031,1.979 2.031,1.979 2.24,1.979 false 2.292,1.865 2.604,2.021 0.313,0.156 10 false *1 0.177,0.875 0.49,1.031 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, remove the 2 through bolts and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 3.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A187214C02
2.365,1.323 2.792,1.323 false 0.563,1.781 0.802,1.781 0.802,1.781 1.083,1.552 false 2.844,1.208 3.156,1.365 0.313,0.156 10 false *1 0.406,1.677 0.719,1.833 0.313,0.156 10 false *2
*1 Starter Commutator End Frame Assembly
*2 Starter Yoke Assembly


Remove the 2 screws and while holding down the field coil lead wire, remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 28140 4.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C08
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Brush Spring
*b Brush


Using a screwdriver, hold the brush spring back and disconnect the starter brush holder assembly.


b.

Disconnect the 4 brushes, and remove the starter brush holder assembly.


Hide 28160 5.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438C01
1.49,0.406 1.938,0.229 1.938,0.229 2.188,0.229 false 1.615,1.958 1.823,1.958 1.823,1.958 2.073,1.635 false 2.229,0.135 2.542,0.333 0.313,0.198 10 false *1 1.417,1.885 1.729,2.083 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER ARMATURE PLATE

a.
A207174C05
0.448,0.229 0.656,0.229 0.656,0.229 0.823,0.365 false 1.698,2.063 1.49,2.063 1.49,2.063 1.323,1.917 false 3.083,0.281 2.917,0.281 2.917,0.281 2.708,0.677 false 2.229,0.917 2.083,0.573 2.083,0.573 1.906,0.573 false 1.76,1.938 1.958,2.104 0.198,0.167 10 false *1 0.292,0.115 0.49,0.281 0.198,0.167 10 false *2 3.135,0.177 3.333,0.344 0.198,0.167 10 false *3 1.76,0.469 1.958,0.635 0.198,0.167 10 false *1
*1 Starter Armature Plate
*2 Repair Service Starter Kit
*3 Starter Yoke Assembly


Remove the starter armature plate from the repair service starter kit or starter yoke assembly.


Hide 7.REMOVE RUBBER SEAL

a.
A409481

Remove the rubber seal from the repair service starter kit.


Hide 8.REMOVE PLANETARY GEAR

a.
A269262

Remove the 3 planetary gears from the repair service starter kit.