Home › General › MAINTENANCE › 2GR-FKS OIL AND OIL FILTER › 2017.09–2019.10
RM33A0E _V1 General _065356 MAINTENANCE _0328821 2GR-FKS OIL AND OIL FILTER A

MAINTENANCE  2GR-FKS OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used engine oil and used engine oil filters at designated disposal sites only.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Clean the oil pan drain plug.


d.

Install a new gasket to the oil pan drain plug.


e.

Install the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 2.REMOVE OIL FILTER CAP ASSEMBLY

a.
A189717C13
1.708,0.292 1.552,0.292 1.552,0.292 1.031,0.563 false 3,1.115 2.844,1.115 2.844,1.115 2.479,1.385 false 1.771,0.188 2.083,0.344 0.313,0.156 10 false *a 3.052,1 3.365,1.156 0.313,0.156 10 false *b
*a Pipe
*b Hose


Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A406884

Remove the oil filter drain plug from the oil filter cap assembly.


c.
A406885C01
2.448,1.729 2.708,1.729 false 2.469,1.938 2.594,1.938 2.594,1.938 2.781,1.844 true 2.75,2.052 3.021,2.052 false 2.292,1.646 2.604,1.802 0.313,0.156 10 false *1 2.313,1.854 2.625,2.01 0.313,0.156 10 false *2 2.604,1.948 2.917,2.104 0.313,0.156 10 false *a
*1 Oil Filter Cap Assembly
*2 O-ring
*a Pipe


Insert the pipe with hose into the oil filter cap assembly.

NOTICE:

Be sure to insert the pipe with the O-ring installed to the oil filter cap assembly.


HINT:

Place the hose end into a container before draining the engine oil from the hose.



d.
A406886

Make sure that the engine oil is completely drained, and remove the pipe with hose and O-ring.

HINT:

Pull the pipe with hose as shown in the illustration to remove it.



e.
A406887N01
1.927,1.25 2.469,1.25 true 2.51,1.156 2.833,1.333 0.323,0.177 10 true SST

Using SST, remove the oil filter cap assembly.

SST
09228-06502  


f.
A272649C05
2.115,0.625 2.573,0.292 2.573,0.292 2.698,0.292 true 2.406,0.979 2.625,0.854 2.625,0.854 2.729,0.854 false 2.156,1.458 2.427,1.677 2.427,1.677 2.531,1.677 true 2.719,0.208 2.958,0.354 0.24,0.146 10 *1 2.74,0.76 3.031,0.917 0.292,0.156 10 *2 2.542,1.594 2.802,1.74 0.26,0.146 10 *3
*1 Oil Filter Element
*2 Oil Filter Cap Assembly
*3 O-ring


Remove the oil filter element and O-ring from the oil filter cap assembly.

NOTICE:

Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.



Hide 15620 3.INSTALL OIL FILTER CAP ASSEMBLY

a.

Clean the inside of the oil filter cap assembly, the threads and O-ring groove.


b.
A337618C11
1.458,1.063 1.542,0.813 1.542,0.813 1.667,0.813 false 3.031,1.156 3.094,0.906 3.094,0.906 3.188,0.906 false 1.688,0.729 2,0.885 0.313,0.156 10 false *1 0.844,1.802 1.156,1.958 0.313,0.156 10 false *a 2.448,1.802 2.76,1.958 0.313,0.156 10 false *b 3.208,0.823 3.385,1.073 0.177,0.25 10 false *1
*1 O-ring
*a Correct
*b Incorrect


Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise engine oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element in the oil filter cap assembly.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and install the oil filter cap assembly.

NOTICE:

Make sure that the O-ring does not get caught between the parts.



f.
A406889C01
2.635,0.531 2.917,0.531 false 2.552,1.177 2.75,1.031 2.75,1.031 2.906,1.031 true 2.49,1.833 2.885,1.833 false 1.438,1.896 1.438,1.375 true 2.917,1.74 3.229,1.896 0.313,0.156 10 false *1 2.927,0.948 3.24,1.104 0.313,0.156 10 false *2 2.938,0.448 3.25,0.604 0.313,0.156 10 false *3 3.031,1.333 3.344,1.49 0.313,0.156 10 false *a 1.313,1.906 1.771,2.104 0.458,0.198 10 false SST
*1 Oil Filter Cap Assembly
*2 O-ring
*3 Oil Pan Sub-assembly
*a No Gap


Using SST, tighten the oil filter cap assembly.

SST
09228-06502  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

·

Do not cross thread the oil filter cap assembly.




g.
A406890C01
2.573,1.99 3,1.99 true 2.438,1.896 2.75,2.052 0.313,0.156 10 false *1
*1 O-ring


Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

NOTICE:

Remove any dirt or foreign matter from the installation surface.



h.

Install the oil filter drain plug to the oil filter cap assembly.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 4.ADD ENGINE OIL

a.
A308107

Add clean engine oil and install the oil filler cap sub-assembly.

NOTICE:

Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If engine oil is on the location indicated by the arrow, replace the belt tensioner.


Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40




Standard Capacity (w/o Engine Oil Cooler)
Item Specified Condition
Drain and refill with oil filter change 5.4 liters (5.7 US qts, 4.8 Imp. qts)
Drain and refill without oil filter change 5.3 liters (5.6 US qts, 4.7 Imp. qts)
Dry fill 6.5 liters (6.9 US qts, 5.7 Imp. qts)

Standard Capacity (w/ Engine Oil Cooler)
Item Specified Condition
Drain and refill with oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
Drain and refill without oil filter change 5.3 liters (5.6 US qts, 4.7 Imp. qts)
Dry fill 6.5 liters (6.9 US qts, 5.7 Imp. qts)


Hide 5.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.