Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2017.09–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328876 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and to adjust the beam axis by using a reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E305141E05
4.385,0.844 4.885,0.615 4.885,0.615 5.26,0.604 false 2.135,0.688 2.385,0.688 2.385,0.688 2.76,0.823 false 0.552,0.073 1.896,0.26 1.344,0.188 10 false Left Side of Vehicle: 4.021,0.073 5.365,0.26 1.344,0.188 10 false Right Side of Vehicle: 5.323,0.521 6.667,0.708 1.344,0.188 10 false Vehicle center line 0.969,0.594 2.313,0.781 1.344,0.188 10 false Vehicle center line 1.313,4.375 2.656,4.563 1.344,0.188 10 false : Inspection Area 0.104,2.448 1.052,2.719 0.948,0.271 10 false 5 m (16.41 ft.) 6.208,2.458 7.156,2.729 0.948,0.271 10 false 5 m (16.41 ft.) 3.219,1.823 4.563,2.01 1.344,0.188 10 false Rear Bumper 0.125,1.719 1.073,1.99 0.948,0.271 10 false 1 m (3.28 ft.) 1.531,3.458 2.479,3.729 0.948,0.271 10 false 6 m (19.68 ft.) 4.854,3.458 5.802,3.729 0.948,0.271 10 false 6 m (19.68 ft.) 6.208,1.708 7.156,1.979 0.948,0.271 10 false 1 m (3.28 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in the inspection area or allow people to enter the inspection area (W 6 m (19.68 ft.) x L 6 m (19.68 ft.) x H 4 m (13.12 ft.)) shown in the illustration.




b.

Place the reflector.

i.

From the center of the rear bumper (center of the emblem), hang a weight with a pointed tip, and mark the rear center point of the vehicle on the ground (mark A).

E359639C01
2.698,2.479 3.146,2.385 false 2.708,2.625 3.156,2.667 false 5.167,1.073 5.781,1.229 false 5.167,0.677 5.771,0.552 true 5.802,0.458 6.115,0.615 0.313,0.156 10 false *a 3.188,2.313 3.5,2.469 0.313,0.156 10 false *b 5.823,1.167 6.135,1.323 0.313,0.156 10 false *c 3.208,2.594 3.365,2.75 0.156,0.156 10 false A
*a String *b Weight
*c Center point - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.



ii.

From the center of the front bumper (center of the emblem), hang a weight with a pointed tip, and mark the front center point of the vehicle on the ground (mark B).

E359640C01
3.844,2.354 3.385,2.24 false 3.844,2.49 3.396,2.615 false 2.021,0.448 1.552,0.521 false 2.063,1.125 1.552,0.948 false 2.083,0.375 2.323,0.552 0.24,0.177 10 true *a 3.177,2.135 3.49,2.292 0.313,0.156 10 false *b 2.125,1.104 2.365,1.292 0.24,0.188 10 true *c 3.229,2.563 3.542,2.719 0.313,0.156 10 false B
*a String *b Weight
*c Center point - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark (B).



iii.
E238824E01
1.439,1.257 1.206,1.541 false 3.022,1.262 3.177,1.627 false 0.633,1.258 1.092,0.453 false 1.092,0.453 1.292,0.453 false 1.321,0.355 2.528,0.516 1.207,0.161 10 Vehicle center line 1.1,1.532 1.261,1.693 0.161,0.161 10 A 3.186,1.624 3.347,1.785 0.161,0.161 10 B

Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).


iv.

Print out the following illustration on a large piece of paper.

E366075E01
3.74,6.833 3.906,6.5 3.906,6.5 4.073,6.5 false 3.344,2.583 3.521,2.917 3.521,2.917 3.688,2.917 false 4.833,4.438 5.167,3.583 5.167,3.583 5.333,3.583 false 2.344,6 2.177,6 2.177,6 2.021,4.448 false 0.104,3.958 1.594,4.198 1.49,0.24 10 false Edge of rear bumper 0.167,0.167 1.542,0.365 1.375,0.198 10 false Printout: 5.396,3.5 6.74,3.719 1.344,0.219 10 false Vehicle center line 3.75,2.833 4.667,3.031 0.917,0.198 10 false Line C 4.146,6.417 5.063,6.615 0.917,0.198 10 false Line C 2.396,5.917 2.688,6.115 0.292,0.198 10 false A 2.667,4 3.583,4.198 0.917,0.198 10 false 54.5° 2.656,4.719 3.573,4.917 0.917,0.198 10 false 54.5°


v.
E334361E02
1.063,2.635 1.333,2.635 1.333,2.635 1.823,2.896 false 2,2.188 2.531,2.563 2.531,2.563 2.74,2.563 false 0.979,1.458 1.146,1.458 1.146,1.458 1.823,1.969 true 0.813,1.385 1.125,1.583 0.313,0.198 10 false A 2.802,2.49 3.427,2.719 0.625,0.229 10 false Printout 0.094,2.552 0.99,2.948 0.896,0.396 10 false Vehicle center line 0.104,0.104 1.094,0.333 0.99,0.229 10 false Vehicle Rear

Place the printout on the floor with the point A aligned with the longitudinal center line of the vehicle.


vi.
E334362E11
0.563,4.125 0.667,4.125 0.667,4.125 0.75,3.75 false 2.875,4.115 2.76,4.115 2.76,4.115 2.656,3.729 false 0.729,3.146 0.833,3.146 0.833,3.146 1.094,3.542 false 2.458,2.594 2.26,2.594 2.26,2.594 1.729,3.167 true 2.604,3.208 2.49,3.208 2.49,3.208 2.292,3.521 false 2.042,4.031 1.927,4.031 1.927,4.031 1.813,3.385 false 2.365,0.167 2.25,0.167 2.25,0.167 1.698,0.552 false 0.354,0.156 1.229,0.365 0.875,0.208 10 false Vehicle front 2.448,0.104 3.292,0.563 0.844,0.458 10 false Vehicle center line 2.521,2.521 2.875,2.708 0.354,0.188 10 false A 0.333,3.052 0.865,3.323 0.531,0.271 10 false String 0.427,4.063 0.781,4.25 0.354,0.188 10 false D 2.917,4.042 3.271,4.229 0.354,0.188 10 false D 2.083,3.969 2.625,4.26 0.542,0.292 10 false Printout 2.656,3.125 3.135,3.406 0.479,0.281 10 false String

Align a piece of string with line C and mark point D at a distance of 2905 mm (9.53 ft.) from point A.


vii.

Set the reflector at the point D shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360E20
4.396,2.25 4.135,1.792 4.135,1.792 4.01,1.792 false 2.74,2.24 3,1.802 3,1.802 3.115,1.802 false 5.958,2.969 6.146,3.333 6.146,3.333 6.302,3.333 false 1.188,2.969 0.979,3.479 0.979,3.479 0.833,3.479 false 1.854,2.583 1.438,1.646 1.438,1.646 1.292,1.646 false 5.906,2.896 6.135,2.302 6.135,2.302 6.292,2.302 false 5.302,2.563 5.792,1.479 5.792,1.479 5.948,1.479 false 1.25,2.927 1,2.156 1,2.156 0.854,2.156 false 0.51,0.135 0.969,0.333 0.458,0.198 10 false LH: 3.448,0.083 3.906,0.281 0.458,0.198 10 false RH: 3.156,1.719 4.073,1.958 0.917,0.24 10 false Rear bumper 1.854,0.24 3.042,0.573 1.188,0.333 10 false Vehicle center line 4.188,0.281 5.646,0.542 1.458,0.26 10 false Vehicle center line 6.365,3.219 7.125,3.469 0.76,0.25 10 false Reflector 0.229,3.427 1.146,3.667 0.917,0.24 10 false Reflector 0.656,1.552 1.25,2.042 0.594,0.49 10 false 2905 mm (9.53 ft) 0.708,2.063 1.625,2.302 0.917,0.24 10 false D 6.344,2.25 6.792,2.583 0.448,0.333 10 false D 6.042,1.406 6.646,1.865 0.604,0.458 10 false 2905 mm (9.53 ft)

NOTICE:
·
E238830E59
0.333,1.417 0.844,1.813 0.51,0.396 10 false 521 mm (1.71 ft.)

Set the reflector so that its center is 521 mm (1.71 ft.) above the ground.

·
E338853E02
2.125,0.729 1.677,1.615 1.677,1.615 1.906,1.615 true 1.958,1.552 3.229,2.083 1.271,0.531 10 false Center of triangular pyramid

The center of the triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that the center of the triangular pyramid faces the blind spot monitor sensor.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor system on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Display or BSM Slave Beam Axis Display.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 5238
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 5239

vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor RH (Master) Blind Spot Monitor Sensor LH (Slave)
Angle -3.6 to +3.6° -3.6 to +3.6°


HINT:

If the results are outside the allowable range, it is possible that the reflector position is incorrect, there is a metallic object near the inspection area or the blind spot monitor sensor installation condition is abnormal, so check the reflector positioning, the inspection area and the blind spot monitor sensor installation condition, and perform the inspection again.




d.

Perform the blind spot monitor beam axis adjustment.

i.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Adjustment or BSM Slave Beam Axis Adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.


Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 5231
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 5232



BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-5°) by using a jig, and that the sensor is 46 to 54° from the line parallel to the vehicle center line.



b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the measurement or angle is within the allowable range to confirm that the blind spot monitor sensor is perpendicular to the floor surface (+/-5°).

HINT:

A digital angle meter can also be used to check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.


E366064E01
5.01,1.24 5.5,0.583 5.5,0.583 5.667,0.583 false 4.677,3.26 5,3.417 5,3.417 5.167,3.417 false 1.271,3.833 1.438,3.833 1.438,3.833 1.635,2.615 false 5.844,3.948 5.844,3.25 5.844,3.25 6.01,3.25 false 2.083,2.333 2.99,3.583 2.99,3.583 3.156,3.583 false 0.115,0.083 2,0.354 1.885,0.271 10 false Rear view of vehicle (RH): 5.729,0.49 6.188,0.688 0.458,0.198 10 false Jig 6.063,3.167 7.063,3.417 1,0.25 10 false Floor surface 5.208,3.344 5.719,3.542 0.51,0.198 10 false Weight 3.198,3.5 4.802,3.75 1.604,0.25 10 false Outward facing surface 0.083,3.75 1.333,4.167 1.25,0.417 10 false Blind Spot Monitor Sensor

E308579E01
1.729,0.875 3.177,1.427 1.448,0.552 10 false Hold this side against the blind spot monitor sensor RH. 4.031,0.885 5.479,1.438 1.448,0.552 10 false Hold this side against the blind spot monitor sensor LH. 3.271,1.719 3.646,1.99 0.375,0.271 10 false Top 1.292,2.677 2.74,3.229 1.448,0.552 10 false Position where string is to be secured 5.344,3.167 5.917,3.646 0.573,0.479 10 false 100 mm (3.94 in.) 2.615,4.385 2.99,4.656 0.375,0.271 10 false A 3.885,4.385 4.26,4.656 0.375,0.271 10 false B 3.104,3.313 3.479,3.583 0.375,0.271 10 false X 3.552,3.313 3.927,3.583 0.375,0.271 10 false Y 1.677,4.99 2.052,5.26 0.375,0.271 10 false + 5,5.021 5.375,5.292 0.375,0.271 10 false - 1.042,6.188 2.5,6.427 1.458,0.24 10 false : Allowable range

Standard
A B
Blind spot monitor sensor RH (Master) 7 mm
(0.276 in.)
-7 mm
(-0.276 in.)
Blind spot monitor sensor LH (Slave) 7 mm
(0.276 in.)
-7 mm
(-0.276 in.)

X Y
Blind spot monitor sensor RH (Master) 5° -5°
Blind spot monitor sensor LH (Slave) 5° -5°


c.
E359641E01
3.198,0.938 3.042,0.5 3.042,0.5 2.875,0.5 false 0.979,1.885 0.844,1.542 0.844,1.542 1.01,1.542 false 2.344,3.667 2.177,3.667 2.177,3.667 1.875,3.156 false 1.375,3.729 1.208,3.729 1.208,3.729 1.063,3.24 false 0.938,3.927 0.771,3.927 0.771,3.927 0.604,3.396 false 0.531,1.521 0.448,1.833 0.448,1.833 0.281,1.833 false 0.052,0.094 1.479,0.354 1.427,0.26 12 false Vehicle rear (LH): 1.708,0.406 3.01,0.615 1.302,0.208 10 false Vehicle center line 1.479,0.823 2.406,1.031 0.927,0.208 10 false Vehicle front 2.417,3.313 3.344,3.521 0.927,0.208 10 false Vehicle rear 2.406,3.583 3.083,3.823 0.677,0.24 10 false Stud bolt 0.146,1.75 0.365,1.979 0.219,0.229 10 false A 1,3.854 3.406,4.094 2.406,0.24 10 false Line parallel to the vehicle center line 1.542,2.063 2.802,2.302 1.26,0.24 10 false 108 mm (4.25 in.) 1.063,1.458 2.406,1.667 1.344,0.208 10 false Stud bolt center line 1.427,3.625 1.646,3.854 0.219,0.229 10 false y

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 78 to 87 mm
(3.07 to 3.43 in.)

Degree Specified Value
A 46 to 54°


HINT:

If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.