Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328876 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E244551E90
3.604,0.698 3.917,0.875 0.313,0.177 10 false BRB 3.427,0.583 3.542,0.76 0.115,0.177 10 false 5 3.604,3.281 3.917,3.458 0.313,0.177 10 false BLB 3.417,3.188 3.531,3.365 0.115,0.177 10 false 5 3.604,4.094 4.042,4.271 0.438,0.177 10 false BLGD 3.344,3.99 3.521,4.167 0.177,0.177 10 false 10 3.354,1.365 3.531,1.542 0.177,0.177 10 false 10 3.604,1.49 4.031,1.646 0.427,0.156 10 false BRGD 1.583,0.854 2.646,1.021 1.063,0.167 10 false ECU-IG1 NO. 4 0.156,0.698 1.146,1.188 0.99,0.49 10 false from IG1-NO. 1 Relay 6.073,1.052 7.115,1.604 1.042,0.552 10 false to CAN Communication System 3.469,4.583 3.833,4.74 0.365,0.156 10 false W6 3.406,2.198 5.021,2.542 1.615,0.344 10 false Blind Spot Monitor Sensor RH 3.469,4.75 5.083,5.094 1.615,0.344 10 false Blind Spot Monitor Sensor LH 0.854,5.313 2.854,5.469 2,0.156 10 false : CAN Communication Line 3.396,2.01 3.802,2.167 0.406,0.156 10 false W5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH POWER SOURCE)
a.

Disconnect the W5 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W5-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
W5-5 (BRB) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH POWER SOURCE)
a.

Disconnect the W6 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W6-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V
W6-5 (BLB) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR