Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0319643 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If there is a communication error with the millimeter wave radar sensor assembly, the forward recognition camera stores DTC U0235.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor After the engine switch is turned on (IG) for 3 seconds or more, when the vehicle is being driven at a speed of 5 km/h (4 mph) or more, a communication error between the millimeter wave radar sensor assembly and forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera



WIRING DIAGRAM

A401976E01
4.198,1.625 6.156,1.854 1.958,0.229 10 false Forward Recognition Camera 4.188,3.99 6.792,4.25 2.604,0.26 10 false Millimeter Wave Radar Sensor Assembly 2.583,0.521 3.958,0.719 1.375,0.198 10 false ECU-IG1 NO. 3 0.688,0.365 3.75,0.563 3.063,0.198 10 false from IG1-NO. 1 Relay 0.594,4.385 4.26,4.583 3.667,0.198 10 false : CAN Communication Line 4.354,0.26 4.51,0.458 0.156,0.198 10 false 7 4.292,0.979 4.531,1.188 0.24,0.208 10 false 10 4.365,2.615 4.521,2.813 0.156,0.198 10 false 8 4.354,3.333 4.51,3.531 0.156,0.198 10 false 1 4.542,0.375 5,0.573 0.458,0.198 10 false IGB 4.531,1.104 4.99,1.302 0.458,0.198 10 false GND 4.542,2.719 5,2.917 0.458,0.198 10 false IGB 4.542,3.469 5.104,3.688 0.563,0.219 10 false SGND 5.396,0.563 6.01,0.76 0.615,0.198 10 false CANH 5.396,0.906 6.01,1.104 0.615,0.198 10 false CANL 5.406,2.917 6.021,3.115 0.615,0.198 10 false CA1P 5.406,3.323 6.021,3.521 0.615,0.198 10 false CA1N 5.854,0.396 6.01,0.594 0.156,0.198 10 false 6 5.844,0.76 6.156,0.958 0.313,0.198 10 false 12 5.854,3.156 6.01,3.354 0.156,0.198 10 false 6 5.854,2.75 6.01,2.948 0.156,0.198 10 false 5 4.188,1.469 4.646,1.667 0.458,0.198 10 false V6 4.188,3.823 4.646,4.021 0.458,0.198 10 false A30 0.698,2.729 3.76,2.927 3.063,0.198 10 false from IG1-NO. 1 Relay 2.583,2.865 3.958,3.063 1.375,0.198 10 false ECU-IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

When pre-collision system DTC U1002 is output, check that the local bus is functioning normally by performing the diagnostic procedure for U1002.


a.

Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK CAN BUS LINE

B

GO TO PRE-COLLISION SYSTEM

3.CHECK CAN BUS LINE
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
A380142C59
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.635,0.24 2.01,0.448 0.375,0.208 10 false V6 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - V6-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the result is not as specified, a malfunction in a CAN communication line is suspected.



e.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE)

4.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C27
1.479,0.167 1.875,0.396 0.396,0.229 0.885,0.792 1.406,1.052 true 1.969,1.198 2.573,1.5 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.979,0.427 0.417,0.229 10 false A30 0.458,0.708 1.073,0.906 0.615,0.198 10 false SGND 2.625,1.438 3.031,1.646 0.406,0.208 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A30 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-8 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (SGND) - Body ground Always Below 1 Ω



f.

Connect the A30 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK POWER SOURCE CIRCUIT (FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK POWER SOURCE CIRCUIT (FORWARD RECOGNITION CAMERA)
a.
A380142C60
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 1.792,1.427 1.958,1.813 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.208 2.073,0.448 0.458,0.24 10 false V6 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB 1.844,1.844 2.302,2.042 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V6-7 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-10 (GND) - Body ground Always Below 1 Ω



f.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
7.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Chassis > LKA/LDA > Clear DTCs
50002 355

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 3 seconds or more.

2.

Drive the vehicle at a speed of 5 km/h (4 mph) or more for 5 seconds or more.




c.

Check for DTCs.

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA