Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065384 PRE-COLLISION _0319645 PRE-COLLISION SYSTEM U

PRE-COLLISION  PRE-COLLISION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Collision 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-collision system on/off status ON or OFF ON: Pre-collision system on
OFF: Pre-collision system off
-
Pre-Collision Safety Warning Buz Pre-collision system warning buzzer Valid or Inval Valid: Pre-collision system warning buzzer operation possible
Inval: Pre-collision system warning buzzer operation not possible
-
Pre-Collision Brake Pre-collision braking function Valid or Inval Valid: Pre-collision braking operation possible
Inval: Pre-collision braking operation not possible
-
PBA Start Pre-collision brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-collision brake assist not operating
Standby: Brake pedal not depressed during pre-collision brake assist operation
Assist Lv1: Brake pedal depressed during pre-collision brake assist operation
Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation
Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)
Brake Assist Standby - - - Not applicable to this vehicle
Pre-Collision Brake Control Pre-collision braking operational status ON or OFF ON: Pre-collision braking operating
OFF: Pre-collision braking not operating
-
AVS Start - - - Not applicable to this vehicle
VGRS Start - - - Not applicable to this vehicle
PBA Control Pre-collision brake assist operational status Valid or Invalid Valid: Pre-collision brake assist control operation possible
Invalid: Pre-collision brake assist control operation not possible
-
Pre-Collision Safety Brake Ind Pre-collision system alarm warning message status ON or OFF ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Collision Alarm Buzzer Pre-collision system warning buzzer status ON or OFF ON: Pre-collision system warning buzzer sounding
OFF: Pre-collision system warning buzzer not sounding
-
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history ON or OFF ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Environment Hist Millimeter wave radar sensor assembly high temperature history Good or Bad Good: No history of high temperature
Bad: History of high temperature
-
Front Radar-Temperature Malfunction History Millimeter wave radar sensor assembly abnormal temperature history ON or OFF ON: History of abnormal temperature
OFF: No history of abnormal temperature
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
If the engine starts 1 second or more after the engine switch was turned on (IG), this item may change to ON.
Front Recognition Camera-Blockage History Forward recognition camera obstruction history ON or OFF ON: History of being obstructed
OFF: No history of being obstructed
-
Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF ON: History of being unavailable
OFF: No history of being unavailable
-
Destination Variation No Destination country for millimeter wave radar sensor assembly Destination Variation No or Not Available Destination Variation No -
Control Mode ECU control mode status Normal or Check Mode Normal: Normal operation
Check Mode: Operating in control mode
-
PCS Operation State Retention Setting PCS operation state retention setting customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 PCS alarm activation distance retention setting 1 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 PCS alarm activation distance retention setting 2 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 PCS alarm activation distance retention setting 3 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
The Number of DTCs Number of trouble codes 0 to 255 Number of DTCs will be displayed -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Collision 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Collision Alarm Buzzer Pre-collision system warning buzzer ON / OFF Test possible with engine switch on (IG), vehicle stopped