Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM
RM33A0E _58 Vehicle Interior _065388 POWER OUTLETS (INT) _0329463 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Status Signal Circuit  


DESCRIPTION

This circuit sends a charging suspension signal from the certification ECU (smart key ECU assembly) to the mobile wireless charger cradle assembly (front console box insert sub-assembly). Based on this signal, the mobile wireless charger cradle assembly (front console box insert sub-assembly) suspends or resumes wireless charging.

HINT:

The wireless charging system uses the same radio wave frequency that is used to perform verification of the electrical key transmitter sub-assembly. Therefore, when the electrical key transmitter sub-assembly verification is being performed, the certification ECU (smart key ECU assembly) sends a charging suspension signal to the wireless charging system to suspend charging.


WIRING DIAGRAM

E312443E12
5.49,0.552 5.948,0.75 0.458,0.198 10 false 3.3 V 1.875,1.156 2.5,1.354 0.625,0.198 10 false WCSW 2.458,1.198 2.917,1.396 0.458,0.198 10 false 7 1.167,1.646 1.615,1.875 0.448,0.229 10 false R13 1.167,1.823 2.781,2.208 1.615,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.219,1.208 4.677,1.406 0.458,0.198 10 false 7 4.438,1.208 4.896,1.406 0.458,0.198 10 false DIS 4.167,2.427 4.625,2.625 0.458,0.198 10 false k1 4.167,2.604 6.76,3.01 2.594,0.406 10 false Mobile Wireless Charger Cradle Assembly (Front Console Box Insert Sub-assembly) 1.646,0.479 2.104,0.677 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY) (DIS TERMINAL)
E216116C26
1.542,0.302 1.865,0.51 0.323,0.208 2.104,1.396 2.542,1.594 false 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 1.635,0.313 1.948,0.51 0.313,0.198 10 false k1 2.583,1.542 3.042,1.74 0.458,0.198 10 false DIS
*a Component with harness connected
(Mobile Wireless Charger Cradle Assembly (Front Console Box Insert Sub-assembly))


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
k1-7 (DIS) - Body ground For 5 seconds after turning ignition switch from off to ACC*1 4.5 to 6.0 V
Device being charged Below 1 V
Charging suspended due to smart entry and start system status*2 4.5 to 6.0 V


*1: When the ignition switch is turned from off to ACC, the mobile wireless charger cradle assembly (front console box insert sub-assembly) monitors the charging suspension signal for 5 seconds. If the charging suspension signal is not 4 V or more for 0.8 seconds or more during monitoring, the mobile wireless charger cradle assembly (front console box insert sub-assembly) determines that there is an open in the charging suspension signal line, blinks (pattern 1) the indicator light (amber), and prohibits operation until the ignition switch is turned from off to ACC again.

*2: For details about conditions when the certification ECU (smart key ECU assembly) sends the charging suspension signal, refer to System Description.

Click hereVehicle Interior>POWER OUTLETS (INT)>WIRELESS CHARGING SYSTEM>SYSTEM DESCRIPTION



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY))
a.

Disconnect the R13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the k1 mobile wireless charger cradle assembly (front console box insert sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R13-7 (WCSW) - k1-7 (DIS) Always Below 1 Ω
R13-7 (WCSW) or k1-7 (DIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR