Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM
RM33A0E _58 Vehicle Interior _065388 POWER OUTLETS (INT) _0329463 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Wireless Charger Illumination Circuit  


DESCRIPTION

When the light control switch is turned to the tail or head position, this circuit sends an illumination signal to the mobile wireless charger cradle assembly (front console box insert sub-assembly).

WIRING DIAGRAM

E216156E03
0.281,1.469 1.385,1.729 1.104,0.26 10 false from TAIL Relay 1.917,1.656 2.438,1.906 0.521,0.25 10 false PANEL 4.063,1.323 4.333,1.573 0.271,0.25 10 false 10 4.094,3.323 4.365,3.573 0.271,0.25 10 false 9 2.771,3.323 3.042,3.573 0.271,0.25 10 false 1 2.417,3.323 2.854,3.573 0.438,0.25 10 false ILL- 4.323,3.323 4.76,3.573 0.438,0.25 10 false ILL- 4.333,1.323 4.771,1.573 0.438,0.25 10 false TAIL 6.073,0.698 6.51,0.948 0.438,0.25 10 false 3.3 V 5.521,2.927 5.958,3.177 0.438,0.25 10 false 3.3 V 6.281,3.125 6.719,3.375 0.438,0.25 10 false 3.3 V 6.479,3.5 6.917,3.75 0.438,0.25 10 false IC 2.01,2.854 2.448,3.104 0.438,0.25 10 false I/F 4.313,4.698 4.729,4.865 0.417,0.167 10 false k1 1.24,3.677 1.656,3.844 0.417,0.167 10 false K21 1.229,3.854 3.146,4.083 1.917,0.229 10 false Combination Meter Assembly 4.313,4.885 6.906,5.396 2.594,0.51 10 false Mobile Wireless Charger Cradle Assembly (Front Console Box Insert Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the k1 mobile wireless charger cradle assembly (front console box insert sub-assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
k1-10 (TAIL) - Body ground Light control switch in off position Below 1 V
Ignition switch off, light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY))
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (ILL-) - k1-9 (ILL-) Always Below 1 Ω
K21-1 (ILL-) or k1-9 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR