Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0329553 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the m3 rear television camera assembly connector.

E366763N03
3.344,0.156 3.76,0.417 0.417,0.26 3.458,0.177 3.917,0.375 0.458,0.198 10 false m3


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m3-6 (CB+) - Body ground GR - Body ground Power source Engine switch on (ACC) 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the m3 rear television camera assembly connector.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m3-3 (CV+) - m3-2 (CV-) B - G Video signal Engine switch on (IG)
Shift lever in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Engine switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
m3-5 (CGND) - Body ground BR - Body ground Camera ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal m3-3 (CV+) - m3-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal m3-3 (CV+) - m3-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY


E380286E02
1.5,0.448 1.885,0.688 0.385,0.24 3.417,0.417 3.802,0.656 0.385,0.24 1.667,2.073 2.052,2.313 0.385,0.24 3.417,2.042 3.802,2.281 0.385,0.24 4.833,1.958 5.219,2.198 0.385,0.24 5.333,0.417 5.719,0.656 0.385,0.24 1.594,0.49 2.01,0.75 0.417,0.26 10 false K3 3.531,0.458 3.844,0.656 0.313,0.198 10 false K2 1.781,2.125 2.198,2.385 0.417,0.26 10 false K4 3.469,2.083 3.885,2.344 0.417,0.26 10 false K135 4.927,2 5.344,2.26 0.417,0.26 10 false RA 5.458,0.469 5.771,0.667 0.313,0.198 10 false K1

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-26 (CSLD) - Body ground Shield - Body ground Shield ground Always Below 1 V
K2-27 (CGND) - Body ground G - Body ground Camera ground Always Below 1 V
K2-28 (V+) - K3-1 (GND1) B - BR Video signal Engine switch on (IG)
Shift lever in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Engine switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
K2-29 (V-) - K3-1 (GND1) W - BR Ground Always Below 1 V
K2-30 (CA+) - K3-1 (GND1) R - BR Rear television camera assembly power supply Engine switch on (ACC) 5.5 to 7.05 V

a.

Reference (Oscilloscope waveform):

i.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Waveform 1 (camera lens not covered, displaying an image)

Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Engine switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2 (camera lens covered, blacking out the screen)

Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Engine switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).