Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM U

2AR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A412929E01
2.448,0.365 2.844,0.635 0.396,0.271 5.75,0.385 6.125,0.656 0.375,0.271 2.51,0.406 2.958,0.667 0.448,0.26 10 false C58 5.792,0.417 6.198,0.656 0.406,0.24 10 false A22

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Smart Entry and Start System.

*2: w/ Drive Mode Switch

*3: w/ Tumble Control Valve

*4: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

A22-1 (BATT) - C58-59 (E1) R - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A22-2 (+B) - C58-59 (E1) L - W-B Power source of ECM Ignition switch ON 11 to 14 V
A22-3 (+B2) - C58-59 (E1) L - W-B Power source of ECM Ignition switch ON 11 to 14 V
A22-6 (IGSW) - C58-59 (E1) B - W-B Ignition switch signal Ignition switch ON 11 to 14 V
A22-9 (STP) - C58-59 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A22-10 (ST1-) - C58-59 (E1) LG - W-B Stop light switch assembly signal
(opposite of voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
A22-13 (CANH) - C58-59 (E1) B - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A22-23 (NSW) - C58-59 (E1) BE - W-B Park/Neutral position switch assembly signal Ignition switch ON, shift lever in P or N Below 1.0 V
Ignition switch ON, shift lever not in P or N 11 to 14 V
A22-26 (CANL) -C58-59 (E1) W - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A22-29 (STA) - C58-59 (E1) G - W-B Starter assembly signal Cranking 6.0 V or higher
A22-30 (NEO)*1 - C58-59 (E1) B - W-B Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation
(See waveform 3)
A22-31 (TACH) - C58-59 (E1) P - W-B Engine speed signal Idling with warm engine Pulse generation
(See waveform 4)
A22-32 (EC) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
A22-33 (TC) - C58-59 (E1) GR - W-B Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A22-41 (FC) - C58-57 (E01) V - W-B Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A22-44 (SPD) - C58-59 (E1) L - W-B Vehicle speed signal from combination meter assembly signal Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A22-46 (MREL) - C58-59 (E1) W - W-B EFI-MAIN NO. 1 relay operation signal Ignition switch ON 11 to 14 V
A22-47 (VPA) - A22-48 (EPA) G - L Accelerator pedal position sensor signal (for engine control) Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
A22-49 (VCPA) - A22-48 (EPA) BE - L Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A22-50 (VPA2) - A22-51 (EPA2) GR - P Accelerator pedal position sensor signal Ignition switch ON,
accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 4.75 V
A22-52 (VCP2) - A22-51 (EPA2) SB - P Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
A22-56 (SPCN)*2 - C58-59 (E1) V - W-B Drive mode siwtch (NORMAL mode) Ignition switch ON 11 to 14 V
Ignition switch ON, NORMAL mode switch being pushed and held (NORMAL mode) 0 to 1.5 V
A22-57 (PWMS)*2 - C58-59 (E1) LG - W-B Drive mode siwtch (SPORT mode) Ignition switch ON 11 to 14 V
Ignition switch ON, SPORT mode switch being pushed and held at SPORT position (SPORT mode) 0 to 1.5 V
A22-60 (RFC) - C58-59 (E1) LG - W-B Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 6)
C58-18 (#20) - C58-57 (E01) G - W-B No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 7)
C58-19 (#30) - C58-57 (E01) LG - W-B No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 7)
C58-20 (#40) - C58-57 (E01) BE - W-B No. 4 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 7)
C58-21 (#10) - C58-57 (E01) B - W-B No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 7)
C58-24 (IA1-)*3 - C58-57 (E01) G - W-B Intake air control valve actuator (for tumble control valve) Idling with cold engine Pulse generation
(See waveform 8)
C58-25 (IA1+)*3 - C58-57 (E01) W - W-B Intake air control valve actuator (for tumble control valve) Idling with cold engine Pulse generation
(See waveform 9)
C58-26 (E04) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C58-27 (HA1A) - C58-26 (E04) R - W-B Air fuel ratio sensor heater operation signal Idling with cold engine Pulse generation
(See waveform 10)
Ignition switch ON 11 to 14 V
C58-28 (ME01) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C58-29 (+BM) - C58-59 (E1) G - W-B Power source of throttle actuator Always 11 to 14 V
C58-30 (M-) - C58-28 (ME01) W - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(See waveform 11)
C58-32 (ACIS) - C58-57 (E01) P - W-B Vacuum switching valve assembly (for acoustic control induction system) operation signal Ignition switch ON 11 to 14 V
C58-33 (PRG) - C58-57 (E01) W - W-B Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 12)
C58-35 (OC1+) - C58-34 (OC1-) LG - BE Camshaft timing oil control valve assembly (for intake camshaft) operation signal Idling Pulse generation
(See waveform 13)
C58-37 (OE1+) - C58-36 (OE1-) R - V Camshaft timing oil control valve assembly (for exhaust camshaft) operation signal Idling Pulse generation
(See waveform 14)
C58-42 (IGT4) - C58-59 (E1) B - W-B No. 4 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 15)
C58-43 (IGT3) - C58-59 (E1) P - W-B No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 15)
C58-44 (IGT2) - C58-59 (E1) R - W-B No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 15)
C58-45 (IGT1) - C58-59 (E1) W - W-B No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 15)
C58-55 (HT1B) - C58-26 (E04) L - W-B Heated oxygen sensor heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C58-57 (E01) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C58-58 (E02) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C58-59 (E1) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C58-60 (M+) - C58-28 (ME01) B - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 16)
C58-71 (IGF1) - C58-59 (E1) G - W-B Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 15)
C58-80 (EV1+) - C58-112 (EV1-) LG - W Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 17)
C58-82 (VV1+) - C58-115 (VV1-) B - R Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 17)
C58-96 (VCIA)*3 - C58-59 (E1) LG - W-B Power source of tumble control valve position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C58-97 (IAC1)*3 - C58-95 (EIA1)*3 B - L Tumble control valve position sensor Ignition switch off to ON 3.0 to 4.0 V
C58-99 (OX1B) - C58-131 (EX1B) B - W Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 18)
C58-100 (A1A+) - C58-59 (E1) L - B-W Air fuel ratio sensor signal Ignition switch ON 3.3 V*4
C58-101 (VTA2) - C58-133 (ETA) W - G Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON,
accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON,
accelerator pedal fully depressed
4.6 to 5.0 V
C58-108 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C58-111 (VCE1) - C58-59 (E1) B - W-B Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C58-114 (NE+) - C58-113 (NE-) B - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 19)
C58-116 (VCV1) - C58-59 (E1) W - W-B Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C58-120 (THW) - C58-119 (ETHW) B - W Engine coolant temperature sensor signal Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C58-122 (KNK1) - C58-121 (EKNK) R - G Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 20)
C58-132 (A1A-) - C58-59 (E1) P - W-B Air fuel ratio sensor signal Ignition switch ON 2.9 V*4
C58-134 (VCTA) - C58-133 (ETA) R - G Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C58-135 (VTA1) - C58-133 (ETA) B - G Throttle position sensor signal (for engine control) Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
3.2 to 4.8 V
C58-137 (VG) - C58-104 (E2G) BE - B Mass air flow meter sub-assembly signal Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C58-138 (THA) - C58-139 (ETHA) P - G Intake air temperature sensor signal Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V

WAVEFORM 1


A292386E01
1.365,1.917 2.104,2.094 0.74,0.177 10 10 μs./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A292387E02
3,1.375 3.344,1.573 0.344,0.198 10 GND 2.781,0.26 3.385,0.469 0.604,0.208 10 1 V/DIV. 1.385,1.885 2.156,2.052 0.771,0.167 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A210050E08
2.833,2.385 3.167,2.542 0.333,0.156 10 GND 1.125,2.75 1.792,3.021 0.667,0.271 10 2 ms./DIV. 2.229,0.563 2.771,0.854 0.542,0.292 10 5 V/DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A292385E01
0.542,1.167 1,1.365 0.458,0.198 10 GND 0.125,0.125 0.948,0.354 0.823,0.229 10 5 V/DIV. 1.75,1.917 2.563,2.104 0.813,0.188 10 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A292384E01
2.813,1.25 3.271,1.448 0.458,0.198 10 GND 1.146,2.01 1.917,2.167 0.771,0.156 10 20 ms./DIV. 2.708,0.135 3.313,0.313 0.604,0.177 10 5 V/DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A282867E08
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 7


A292383E01
0.667,1.583 1.125,1.781 0.458,0.198 10 GND 1.865,1.906 2.75,2.104 0.885,0.198 10 20 ms./DIV. 0.531,0.177 1.417,0.375 0.885,0.198 10 20 V/DIV.

No. 1 (to No. 4) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A292389E01
0.667,1.333 1.125,1.531 0.458,0.198 10 GND 0.646,0.188 1.219,0.385 0.573,0.198 10 5 V/DIV. 1.833,1.844 2.531,2.042 0.698,0.198 10 1 ms./DIV.

Negative Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal
ECM Terminal Name Between IA1- and E01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with cold engine


WAVEFORM 9


A292388E01
0.667,1.333 1.125,1.531 0.458,0.198 10 GND 0.635,0.156 1.25,0.365 0.615,0.208 10 5 V/DIV. 1.875,1.854 2.563,2.073 0.688,0.219 10 1 ms./DIV.

Positive Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal
ECM Terminal Name Between IA1+ and E01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with cold engine


WAVEFORM 10


A205412E06
2.646,0.042 3.25,0.229 0.604,0.188 10 5 V/DIV. 2.698,0.906 3.063,1.073 0.365,0.167 10 GND 1.156,1.865 1.917,2.042 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 11


A245848E01
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A218020E09
2.667,0.177 3.365,0.448 0.698,0.271 10 10 V/DIV. 2.802,0.948 3.26,1.292 0.458,0.344 10 GND 1.188,1.792 2,2 0.813,0.208 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 13


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 14


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 15


A289263E01
2.844,0.857 3.210,1.059 0.366,0.202 10 GND 2.844,1.502 3.175,1.704 0.331,0.202 10 GND 0.058,0.41 0.435,0.915 0.376,0.504 10 CH1 (IGT) 0.021,1.193 0.440,1.551 0.419,0.358 10 CH2 (IGF1) 0.03,0.036 0.574,0.213 0.545,0.177 10 2 V/DIV. 1.154,1.844 1.905,1.988 0.751,0.145 10 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF1 Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 16


A208000E44
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 17


A255508E16
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.646 0.427,0.813 0.323,0.167 10 CH1 0.125,1.469 0.448,1.635 0.323,0.167 10 CH2 0.052,0.813 0.427,1.01 0.375,0.198 10 (VV1) 0.063,1.625 0.458,1.813 0.396,0.188 10 (EV1) 3.042,0.823 3.365,1.021 0.323,0.198 10 GND 3.031,1.594 3.375,1.854 0.344,0.26 10 GND 1.302,1.896 2.052,2.073 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A292382E01
0.615,1.469 1.073,1.667 0.458,0.198 10 GND 0.479,0.177 1.469,0.365 0.99,0.188 10 0.2 V/DIV. 1.854,1.906 2.844,2.094 0.99,0.188 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the item O2S B1S2 shows the values input to the ECM from the heated oxygen sensor.



WAVEFORM 19


A254145E10
2.984,0.964 3.337,1.167 0.353,0.202 10 GND 0.067,0.058 0.612,0.235 0.545,0.177 10 5 V/DIV. 1.22,1.917 1.972,2.062 0.751,0.145 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 20


A283572E06
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.