Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to IGSW of the ECM. When the transistor in the MREL circuit operates, current flows from the battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A413386E04
4.656,0.938 5.656,1.25 1,0.313 10 false EFI NO. 1 4.698,0.635 4.854,0.833 0.156,0.198 10 false 2 5.021,0.646 5.177,0.844 0.156,0.198 10 false 1 5.635,0.604 5.792,0.802 0.156,0.198 10 false 2 5.552,0.771 6.01,0.969 0.458,0.198 10 false A22 5.906,0.781 6.219,0.979 0.313,0.198 10 false +B 5.521,1.271 5.979,1.469 0.458,0.198 10 false A22 5.604,1.115 5.76,1.313 0.156,0.198 10 false 3 5.885,1.281 6.344,1.479 0.458,0.198 10 false +B2 5.542,1.771 6,1.969 0.458,0.198 10 false A22 5.594,1.583 5.906,1.781 0.313,0.198 10 false 46 5.896,1.771 6.51,1.969 0.615,0.198 10 false MREL 3.615,2.083 4.906,2.417 1.292,0.333 10 false EFI-MAIN NO. 1 3.573,1.646 3.729,1.844 0.156,0.198 10 false 1 4.406,1.635 4.563,1.833 0.156,0.198 10 false 2 3.573,1.146 3.729,1.344 0.156,0.198 10 false 3 4.406,1.146 4.563,1.344 0.156,0.198 10 false 5 0.875,1.458 1.969,1.885 1.094,0.427 10 false EFI-MAIN NO. 1 5.896,2.802 6.51,3 0.615,0.198 10 false IGSW 5.542,2.958 6,3.156 0.458,0.198 10 false A22 5.594,2.76 5.75,2.958 0.156,0.198 10 false 6 4.729,3.177 5.74,3.531 1.01,0.354 10 false ECU-IG2 NO. 1 5.552,5.083 6.01,5.281 0.458,0.198 10 false C58 5.583,4.917 5.896,5.115 0.313,0.198 10 false 59 5.885,5.104 6.198,5.302 0.313,0.198 10 false E1 6.281,5.99 6.74,6.188 0.458,0.198 10 false ECM 4.417,2.813 4.573,3.01 0.156,0.198 10 false 3 3.573,2.823 3.729,3.021 0.156,0.198 10 false 5 3.625,3.344 3.781,3.542 0.156,0.198 10 false 2 4.417,3.344 4.573,3.542 0.156,0.198 10 false 1 1.49,3.135 2.229,3.417 0.74,0.281 10 false IG2-MAIN 3.688,3.802 4.458,4.042 0.771,0.24 10 false IG2 NO. 1 3.083,4.458 3.542,4.656 0.458,0.198 10 false IG1 3.458,4.417 3.646,4.646 0.188,0.229 10 false 8 2.323,4.448 2.781,4.646 0.458,0.198 10 false AM1 2.104,4.427 2.26,4.625 0.156,0.198 10 false 7 2.021,4.906 2.479,5.104 0.458,0.198 10 false K30 2.375,4.906 4.281,5.177 1.906,0.271 10 false Ignition Switch Assembly*2 4.021,4.458 4.333,4.656 0.313,0.198 10 false *2 1.896,4.427 2.208,4.625 0.313,0.198 10 false *2 1.271,4.417 1.583,4.615 0.313,0.198 10 false *2 0.625,4.417 0.938,4.615 0.313,0.198 10 false *2 4.552,5.365 4.865,5.563 0.313,0.198 10 false *1 0.573,5.188 1.646,5.385 1.073,0.198 10 false FL MAIN 0.708,6.031 1.781,6.229 1.073,0.198 10 false Battery 2.229,5.906 2.844,6.104 0.615,0.198 10 false IG1D 2.667,5.875 2.979,6.073 0.313,0.198 10 false 17 1.542,6.344 2,6.542 0.458,0.198 10 false K62 1.521,6.51 3.042,6.958 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly)*1 3.271,6.927 5.833,7.25 2.563,0.323 10 false *1: w/ Smart Entry and Start System 3.26,7.281 5.833,7.583 2.573,0.302 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-59 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
A413387C01
0.219,0.885 0.594,1.177 0.375,0.292 1.479,1.708 1.99,0.885 true 0.177,0.208 0.49,0.406 0.313,0.198 10 false *a 0.281,0.927 0.74,1.125 0.458,0.198 10 false A22 1.26,1.74 1.875,1.938 0.615,0.198 10 false IGSW
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-6 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

7.INSPECT IG2 NO. 1 RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay) - A22-46 (MREL) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A22-2 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A22-3 (+B2) Always Below 1 Ω
2 (EFI-MAIN NO. 1 relay) or A22-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay), A22-2 (+B) or A22-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A402439C01
0.135,0.146 0.448,0.406 0.313,0.26 10 false *1 2.26,0.99 2.573,1.25 0.313,0.26 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

7.INSPECT IG2 NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)

NG

REPLACE IG2 NO. 1 RELAY

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - A22-6 (IGSW) Always Below 1 Ω
3 (IG2 NO. 1 relay) or A22-6 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)
A402425C01
0.177,0.177 0.49,0.375 0.313,0.198 10 false *1 2.271,1 2.583,1.198 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 IG2 NO. 1 Relay


a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG2 NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY)

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)
a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IG2 NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Smart Entry and Start System) A
OK (w/o Smart Entry and Start System) B
NG C



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)

B

12.INSPECT IGNITION SWITCH ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - 1 (IG2 NO. 1 relay) Always Below 1 Ω
K62-17 (IG1D) or 1 (IG2 NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2AR-FE (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 NO. 1 RELAY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 NO. 1 RELAY)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K30-8 (IG1) - 1 (IG2 NO. 1 relay) Always Below 1 Ω
K30-8 (IG1) or 1 (IG2 NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR