Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P061512  Starter Relay Circuit Short to Battery  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery All of the following conditions are met, and battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

ST relay

·

Park/neutral position switch assembly

·

Starter relay (ST) circuit

·

ECM


Comes on DTC stored SAE Code: P0617

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A231469E84
1.229,1.979 1.604,2.156 0.375,0.177 10 false Idling 0.26,2.25 1.656,2.583 1.396,0.333 10 false Engine Switch on (IG) 1.052,0.813 1.646,1.042 0.594,0.229 10 false 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.406,2.521 0.406,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) [A].

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 5 seconds or more [B].

10.

Drive the vehicle at a speed of 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P061512.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A408705E03
5.615,1.01 6.073,1.208 0.458,0.198 10 false A23 5.604,0.573 6.063,0.771 0.458,0.198 10 false A23 5.604,1.427 6.063,1.625 0.458,0.198 10 false C96 5.969,0.594 6.427,0.792 0.458,0.198 10 false NEO 5.969,1 6.427,1.198 0.458,0.198 10 false STA 5.969,1.417 6.427,1.615 0.458,0.198 10 false NSW 5.635,0.365 5.948,0.563 0.313,0.198 10 false 30 5.656,0.813 5.969,1.01 0.313,0.198 10 false 43 5.615,1.219 6.073,1.417 0.458,0.198 10 false 106 6.281,1.698 6.74,1.896 0.458,0.198 10 false ECM 1.167,3.052 1.479,3.25 0.313,0.198 10 false NE 1,3.552 1.615,3.75 0.615,0.198 10 false STAR 1.094,4.042 1.552,4.24 0.458,0.198 10 false STA 1.479,2.969 1.792,3.167 0.313,0.198 10 false 16 1.51,3.469 1.667,3.667 0.156,0.198 10 false 9 1.5,3.938 1.813,4.135 0.313,0.198 10 false 20 0.292,4.365 0.75,4.563 0.458,0.198 10 false A13 0.583,4.375 2.125,5.042 1.542,0.667 10 false Certification ECU (Smart Key ECU Assembly) 1.042,5.385 2.271,5.583 1.229,0.198 10 false ST NO. 1 2.094,5.104 2.25,5.302 0.156,0.198 10 false 5 2.094,5.479 2.25,5.677 0.156,0.198 10 false 1 2.906,5.094 3.063,5.292 0.156,0.198 10 false 3 2.917,5.469 3.073,5.667 0.156,0.198 10 false 2 2.479,5.865 2.792,6.063 0.313,0.198 10 false ST 3.281,4.365 3.74,4.563 0.458,0.198 10 false C55 3.594,4.365 4.938,5.365 1.344,1 10 false Park/Neutral Position Switch Assembly 3.969,5.219 4.583,5.417 0.615,0.198 10 false C61 3.969,6.021 4.427,6.219 0.458,0.198 10 false C74 4.042,4.99 4.198,5.188 0.156,0.198 10 false 1 4.042,5.792 4.198,5.99 0.156,0.198 10 false 1 0.458,7.167 1.531,7.365 1.073,0.198 10 false FL MAIN 0.594,7.948 1.667,8.146 1.073,0.198 10 false Battery 4.219,6.333 6.667,6.531 2.448,0.198 10 false Starter Assembly 3.438,3.938 3.594,4.135 0.156,0.198 10 false 9 4.521,3.948 4.677,4.146 0.156,0.198 10 false 4 3.646,3.938 3.802,4.135 0.156,0.198 10 false L 4.302,3.948 4.458,4.146 0.156,0.198 10 false B 4.354,5.219 4.969,5.417 0.615,0.198 10 false ST 4.354,6.021 4.969,6.219 0.615,0.198 10 false B

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter SW
Engine switch on (IG) OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the engine switch on (IG), GTS connected and Data List item "Starter SW" selected.


Result:
Proceed to
OK
NG


HINT:

If the starter assembly operates continuously when the engine switch is turned on (IG), proceed to the next step without reading the Data List item "Starter SW".



OK

NG

2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A402442C04
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


HINT:

The purpose of this step is to check for ST relay terminal voltage under abnormal conditions.


a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Turn the engine switch on (IG).


c.

Measure the voltage between ST relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the engine switch on (IG) and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the engine switch on (IG), one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A402442C04
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A402442C04
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Remove the ST relay from the engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-43 (STA), C55-9 (L), A13-20 (STA) or 2 (ST relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK SMART ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR