Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › CANISTER (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065344 A25A-FKS EMISSION CONTROL _0328569 CANISTER(w/ Canister Pump Module) A

A25A-FKS EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 17420 1.REMOVE CENTER EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A401954

Remove the 4 bolts and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly.


b.

Remove the center exhaust pipe assembly from the exhaust pipe support.


c.

Remove the 2 gaskets from the center exhaust pipe assembly and front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 48832A 2.REMOVE REAR NO. 1 STABILIZER BAR BRACKET

a.
A402236

Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets from the vehicle body.


Hide 77740 3.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.

Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A401923C01
1.615,0.563 2,0.563 2,0.563 2.271,1.031 true 2.583,2.271 2.938,2.271 false 1.833,2.063 2.01,2.063 2.01,2.063 2.188,1.927 false 5.115,0.927 5.344,0.927 5.344,0.927 5.427,1.365 false 6.552,0.958 6.396,0.958 6.396,0.958 6.302,1.427 false 5.615,1.99 5.615,2.344 true 6.042,2.135 6.042,2.49 true 1.427,0.479 1.646,0.677 0.219,0.198 10 true *1 6.594,0.875 6.844,1.094 0.25,0.219 10 false *2 2.99,2.177 3.24,2.365 0.25,0.188 10 false *a 1.667,1.979 1.927,2.177 0.26,0.198 10 false *b 4.948,0.833 5.198,1.042 0.25,0.208 10 false *c 5.542,2.354 5.802,2.542 0.26,0.188 10 false *d 5.969,2.49 6.219,2.677 0.25,0.188 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



b.

Disconnect the vent line hose from the canister (charcoal canister assembly).

A401924C01
3.104,1.01 3.594,0.75 3.594,0.75 3.938,0.75 true 2.094,2.063 2.25,2.063 2.25,2.063 2.406,1.917 false 2.792,2.25 3.125,2.25 false 5.115,0.854 5.323,0.854 5.323,0.854 5.427,1.354 false 6.635,0.927 6.448,0.927 6.448,0.927 6.323,1.427 false 6.042,2.135 6.042,2.479 true 5.615,1.99 5.615,2.417 true 3.979,0.688 4.229,0.896 0.25,0.208 10 false *1 6.656,0.844 6.896,1.031 0.24,0.188 10 false *2 3.156,2.167 3.469,2.323 0.313,0.156 10 false *a 1.938,1.969 2.198,2.177 0.26,0.208 10 false *b 4.958,0.76 5.229,0.99 0.271,0.229 10 false *c 5.542,2.438 5.771,2.667 0.229,0.229 10 false *d 5.958,2.49 6.271,2.646 0.313,0.156 10 false *a
*1 Vent Line Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the vent line hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the vent line hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the vent line hose.



c.
A401925

Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).


d.
A401926C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts.


e.

Disengage the clip from the canister (charcoal canister assembly).


f.
A401927

Disengage the claw and remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.


g.
A402237

Remove the clip from the vehicle body.


Hide 77730A 4.REMOVE NO. 2 CHARCOAL CANISTER SUB-ASSEMBLY

a.
A401928C01
1.333,0.625 1.667,0.625 true 2.354,2 2.563,2 2.563,2 2.615,2.323 true 1.781,2.24 1.99,2.24 1.99,2.24 2.063,2.365 true 2.281,2.917 2.281,3.125 true 1.146,0.552 1.365,0.729 0.219,0.177 10 true *1 1.604,2.167 1.896,2.354 0.292,0.188 10 false *2 2.208,3.125 2.458,3.313 0.25,0.188 10 false *a 2.188,1.917 2.427,2.094 0.24,0.177 10 false *b
*1 Air Line Tube
*2 Pipe (Leak Detection Pump Sub-assembly)
*a Tube Connector
*b O-ring
V100135

Pinch
V100136

Pull off


Disconnect the air line tube from the leak detection pump sub-assembly.

NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull to release them.



i.

Push the air line tube firmly toward the leak detection pump sub-assembly.


ii.

Pinch the tube connector as shown in the illustration.


iii.

Pull off the air line tube from the pipe (leak detection pump sub-assembly).



b.
A401947

Disconnect the leak detection pump sub-assembly connector.


c.
A401929

Remove the 3 nuts and No. 2 charcoal canister sub-assembly from the vehicle body.


Hide 77740R 5.REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.

Before removing the leak detection pump sub-assembly, clean the No. 2 charcoal canister sub-assembly by blowing air into it to ensure that the No. 2 charcoal canister sub-assembly is free of foreign matter.

NOTICE:
·

Make sure to clean the No. 2 charcoal canister sub-assembly using air only.

·

Do not use gasoline, thinners or solvents.




b.
A401931C01
1.198,1.76 1.198,2 false 1.125,1.979 1.417,2.167 0.292,0.188 10 false *a
*a Protective Tape


While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.


c.

Check if the No. 2 charcoal canister sub-assembly contains foreign matter such as mud or water.

i.
A377739

Visually check that the inside of the No. 2 charcoal canister sub-assembly is free of foreign matter.


ii.

Hold the No. 2 charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.

If the No. 2 charcoal canister sub-assembly contains foreign matter, replace it.