Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING(for Moon Roof) › from 2017.12
RM33A0E _59 Vehicle Exterior _065391 SLIDING ROOF / CONVERTIBLE _0341610 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  REASSEMBLY  


PROCEDURE

Hide 63209 1.INSTALL ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B468973C01
0.729,0.573 1.021,0.365 true 0.302,0.688 0.177,0.594 true 2.458,1.135 2.698,1 true 2.469,1.438 2.708,1.302 true 0.01,0.469 0.323,0.625 0.313,0.156 10 false *a 1.021,0.24 1.333,0.396 0.313,0.156 10 false *b 2.302,1.344 2.615,1.5 0.313,0.156 10 false *a 2.292,1.042 2.604,1.198 0.313,0.156 10 false *b
*a Guide
*b Spring
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Move the roof wind deflector panel sub-assembly in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides and install the roof wind deflector panel sub-assembly.


b.

Push each spring in the direction indicated by the arrow (2) shown in the illustration to engage the 2 springs.

NOTICE:

Make sure that the springs are securely engaged.



Hide 63205A 2.INSTALL SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

a.
B468955C01
0,0 0,0 false
V113146

Hold Position


Hold down the roof wind deflector panel sub-assembly.


b.
B468957C01
1.208,3.833 1.208,3.49 true 1.135,3.844 1.448,4 0.313,0.156 10 false *a
*a Protective Tape
V113146

Push Position
V113147

Install in this Direction


Using a screwdriver, slide the sliding roof drive cable LH as shown in the illustration to install it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side.




c.
B468958C01
2.094,0.625 2.302,0.406 true 1.573,0.646 1.385,0.417 true 2.083,1.01 1.844,1.344 1.844,1.344 1.604,0.99 true 1.75,1.365 1.958,1.563 0.208,0.198 10 true *a 1.167,0.281 1.375,0.479 0.208,0.198 10 true *a 2.313,0.292 2.521,0.49 0.208,0.198 10 true *a
*a Alignment Mark


Adjust Fully Closed Position:

i.

Using a screwdriver, slide the sliding roof drive cable LH in either direction and align the alignment marks as shown in the illustration.

HINT:

Use the same procedure for the RH side.




d.
B468959C01
0,0 0,0 false
V113147

Install in this Direction


Insert the rear roof drip channel into the sliding roof housing sub-assembly as shown in the illustration.


e.

Engage the 2 claws as shown in the illustration to install the rear roof drip channel.

B468960C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 63306 3.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B468961C01
0,0 0,0 false
V113147

Install in this Direction


Insert the sunshade trim sub-assembly into the sliding roof housing sub-assembly as shown in the illustration to install it.


b.
B468962C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear sliding roof sunshade stopper as shown in the illustration.

HINT:

Use the same procedure for the RH side.



c.
B468963C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 claws.

HINT:

Use the same procedure for the RH side.



d.

Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (2) shown in the illustration to engage the guide.

HINT:

Use the same procedure for the RH side.



e.

Install the sliding roof piece sub-assembly LH with the screw.

HINT:

Use the same procedure for the RH side.



Hide 63260A 4.INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.

Apply MP grease to the gear of the sliding roof drive gear sub-assembly.


b.
B468949

Install the sliding roof drive gear sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
B468964C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw as shown in the illustration.


d.

Install the map light bracket with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)