Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for 2AR-FE) › 2017.12–2018.08
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0327281 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE)  U0100  Lost Communication with ECM / PCM "A"  U0104  Lost Communication with Cruise Control Module  U0122  Lost Communication With Vehicle Dynamics Control Module  U0125  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication With Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

Condition 1:
·

The ECM communicates with each sensor and ECU via CAN communication.


Condition 2:
·

The millimeter wave radar sensor assembly communicates with each sensor and ECU via CAN communication.


If any malfunction is detected in a CAN communication circuit, one or more CAN communication system DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A"
Condition 1:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the ECM continuously receives a communication cut-off signal from the skid control ECU (brake actuator assembly) for approximately 1 second or more.


Condition 2:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, a communication error between the ECM and millimeter wave radar sensor assembly is detected for approximately 0.1 seconds or more.


Condition 1:
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


Condition 2:
·

CAN communication system

·

ECM

·

Millimeter wave radar sensor assembly


U0104 Lost Communication with Cruise Control Module
Condition 1:
·

When the ignition switch is ON and the dynamic radar cruise control system is operating, a communication error between the millimeter wave radar sensor assembly and ECM is detected for 1 second or more.


Condition 1:
·

CAN communication system

·

ECM

·

Millimeter wave radar sensor assembly


U0122 Lost Communication with Vehicle Dynamics Control Module
Condition 1:
·

When the ignition switch is ON and the dynamic radar cruise control system is operating, a communication error between the skid control ECU (brake actuator assembly) and ECM is detected for approximately 2.6 seconds or more.


Condition 1:
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


U0125 Lost Communication with Yaw Rate Sensor Module
Condition 2:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, a communication error between the yaw rate and acceleration sensor (airbag sensor assembly) and millimeter wave radar sensor assembly is detected for approximately 0.1 seconds or more.


Condition 2:
·

CAN communication system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Millimeter wave radar sensor assembly


U0126 Lost Communication With Steering Angle Sensor Module
Condition 2:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, a communication error between the steering sensor and millimeter wave radar sensor assembly is detected for approximately 0.1 seconds or more.


Condition 2:
·

CAN communication system

·

Steering sensor

·

Millimeter wave radar sensor assembly


U0129 Lost Communication with Brake System Control Module
Condition 2:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, a communication error between the skid control ECU (brake actuator assembly) and millimeter wave radar sensor assembly is detected for approximately 0.1 seconds or more.


Condition 2:
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Millimeter wave radar sensor assembly



PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Powertrain > Radar Cruise1 > Clear DTCs
50002 239
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control main switch.

3.

Drive the vehicle at 5 km/h (3 mph) or more for 5 seconds or more.




c.

Check for DTCs.

Powertrain > Radar Cruise1 > Trouble Codes
50001 239
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC U0100, U0104, U0122, U0125, U0126 and U0129 are not output A
DTC U0100, U0104, U0122, U0125, U0126 or U0129 is output B



A

B