Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.12–2019.10
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0322781 AUTOMATIC TRANSAXLE SYSTEM J

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S and moved toward "-" or "+", it is possible to select different shift ranges (S1 to S8).

Moving the shift lever toward "+" increases the shift range by one, and moving the shift lever toward "-" decreases the shift range by one.

WIRING DIAGRAM

C318220E18
0.198,0.625 1.083,1.354 0.885,0.729 10 false from ECU-IG1 NO. 3 Fuse 1.688,2.646 3.823,3.24 2.135,0.594 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.688,2.49 2.26,2.813 0.573,0.323 10 false K29 2.083,0.49 2.396,0.688 0.313,0.198 10 false IG 2.063,1.854 2.375,2.042 0.313,0.188 10 false E 3.271,0.49 3.583,0.677 0.313,0.188 10 false S 3.021,1.177 3.635,1.375 0.615,0.198 10 false SFTU 3.021,1.854 3.635,2.052 0.615,0.198 10 false SFTD 5.521,0.51 5.833,0.698 0.313,0.188 10 false S 5.521,1.188 6.135,1.385 0.615,0.198 10 false SFTU 5.521,1.875 6.135,2.073 0.615,0.198 10 false SFTD 5.875,2.469 6.188,2.667 0.313,0.198 10 false A23 5.875,2.635 6.458,3.167 0.583,0.531 10 false ECM 1.865,0.49 2.021,0.688 0.156,0.198 10 false 4 1.865,1.854 2.177,2.052 0.313,0.198 10 false 2 3.521,1.646 3.833,1.844 0.313,0.198 10 false 1*1 3.531,0.99 3.844,1.188 0.313,0.198 10 false 3*1 5.26,0.51 5.573,0.708 0.313,0.198 10 false 17 5.271,1.188 5.583,1.385 0.313,0.198 10 false 38 5.26,1.875 5.573,2.073 0.313,0.198 10 false 37 6.25,1.01 6.708,1.208 0.458,0.198 10 false 12 V 6.25,1.688 6.708,1.885 0.458,0.198 10 false 12 V 3.521,0.5 3.833,0.698 0.313,0.198 10 false 5 3.531,1.177 3.844,1.375 0.313,0.198 10 false 1*2 3.531,1.844 3.844,2.042 0.313,0.198 10 false 3*2 0.229,3.208 1.917,3.406 1.688,0.198 10 false *1: for LHD 0.24,3.458 1.927,3.656 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (Shift SW Status (S Range))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Shift SW Status (S Range).


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Sport (S) mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Sport Shift Up SW and Sport Shift Down SW.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" or "+" shift paddle switch operated

·

OFF: Shift lever not held in "+" and "+" shift paddle switch released


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" or "-" shift paddle switch operated

·

OFF: Shift lever not held in "-" and "-" shift paddle switch released


-
Powertrain > Engine > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 372 26,25

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K29 transmission control switch connector.


b.
C251980C84
1.719,1.708 1.719,1.281 true 2.167,1.844 1.927,1.292 true 2.542,1.708 2.146,1.281 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.531,1.74 2.094,1.948 0.563,0.208 10 false SFTU*A 2.146,1.865 2.323,2.031 0.177,0.167 10 false E 2.469,1.729 3.094,1.927 0.625,0.198 10 false SFTD*A 1.531,1.896 2.094,2.104 0.563,0.208 10 false SFTD*B 2.469,1.896 3.094,2.094 0.625,0.198 10 false SFTU*B
*A for LHD
*B for RHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" (Up shift) Below 1 Ω
Shift lever not held in "+" (Up shift) 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" (Down shift) Below 1 Ω
Shift lever not held in "-" (Down shift) 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" (Up shift) Below 1 Ω
Shift lever not held in "+" (Up shift) 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" (Down shift) Below 1 Ω
Shift lever not held in "-" (Down shift) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.

Disconnect the K29 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Connect the K29 transmission control switch connector.


b.

Disconnect the A23 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-38 (SFTU) - Body ground Shift lever held in "+" (Up shift) Below 1 Ω
A23-38 (SFTU) - Body ground Shift lever not held in "+" (Up shift) 10 kΩ or higher
A23-37 (SFTD) - Body ground Shift lever held in "-" (Down shift) Below 1 Ω
A23-37 (SFTD) - Body ground Shift lever not held in "-" (Down shift) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C277025C47
0.802,1.802 1.219,1.385 true 1.615,1.781 1.479,1.396 true 1.573,1.833 1.885,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the K29 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
a.

Disconnect the K29 transmission control switch connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K29-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the K29 transmission control switch connector.


b.

Disconnect the A23 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-5 (S) - A23-17 (S) Always Below 1 Ω
K29-5 (S) or A23-17 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)