Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 16 inch Front Disc Brake) › from 2017.12
RM33A0E _54 Brake _065367 BRAKE (FRONT) _0341735 FRONT BRAKE(for 16 inch Front Disc Brake) A

BRAKE (FRONT)  FRONT BRAKE(for 16 inch Front Disc Brake)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the front disc brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C369838C01
2.021,0.958 3,0.958 true 2.031,1.01 2.823,1.01 2.823,1.01 2.823,0.958 true 3.042,0.875 3.229,1.052 0.188,0.177 10 true *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C369848C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C369849C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).


b.

Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).


c.
C369850C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 front disc brake cylinder slide pins.


d.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


e.

Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

for Type A:

i.
C378959C01
1.833,0.719 2.5,0.719 true 1.833,4.042 2.5,4.042 true 2.542,0.635 2.854,0.792 0.313,0.156 10 false *1 2.542,3.958 2.854,4.115 0.313,0.156 10 false *1
*1 Front Disc Brake Pad Support Plate
V100155

Identification Paint (Blue)


Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Install the 2 front disc brake pad support plates with the identification paint is mounted on the inner side of the vehicle.




b.

for Type B:

i.

Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.




Hide 04945 6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 7.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




Hide 47750 8.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313J 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 10.BLEED BRAKE LINE

Hide 11.INSTALL FRONT WHEEL