Wear protective gloves. Sharp areas on the parts may injure your hands.
87510T
1.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71075B
2.INSTALL BENCH TYPE REAR SEAT CUSHION COVER
When installing a bench type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the 24 claws.
Be careful not to damage the bench type rear seat cushion cover.
Engage the 20 hooks.
Be careful not to damage the bench type rear seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the bench type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.
Using hog ring pliers, install 6 new hog rings.
Be careful not to damage the bench type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.
Engage the 6 hooks.
Be careful not to damage the bench type rear seat cushion cover.
Engage the 4 fasteners to install the bench type rear seat cushion cover to the rear seat cushion pad sub-assembly.
|
Fastener | - | - |
Be careful not to damage the bench type rear seat cushion cover.
73733
3.INSTALL CHILD RESTRAINT SEAT BASE COVER
|
Install in this Direction |
Engage the guide and claw as shown in the illustration.
Install the child restraint seat base cover with the screw.
Use the same procedure for all child restraint seat base cover.
73731
4.INSTALL CHILD RESTRAINT SEAT COVER
|
Install in this Direction |
Engage the 2 guides and 2 claws to install the child restraint seat cover as shown in the illustration.
Use the same procedure for all child restraint seat covers.
72740A
5.INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH
Install the rear seat reclining adjuster assembly LH with the 2 bolts and 2 nuts in the order shown in the illustration.
Connect the connector.
72730A
6.INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH
Use the same procedure as for the LH side.
71095S
7.INSTALL CENTER SEATBACK COVER SUB-ASSEMBLY
Install the center seatback cover sub-assembly to the center seatback pad sub-assembly.
Engage the 7 hooks to install the center seatback cover with pad to the center seatback frame sub-assembly.
71931A
8.INSTALL REAR SEAT HEADREST SUPPORT (for Center Seat)
|
Install in this Direction |
Engage the 4 claws to install the 2 rear seat headrest supports as shown in the illustration.
82176
9.INSTALL REAR CONSOLE BOX WIRE (for Center Seat)
Engage the 3 clamps to install the rear console box wire.
Install the rear seat center armrest pad to the rear seat center armrest box.
72806D
10.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY (for Center Seat)
|
Install in this Direction |
Install the rear seat center armrest cup holder sub-assembly with the 2 screws as shown in the illustration.
Engage the 16 claws to install the 2 rear seat center armrest plates.
Install the 2 screws and rear seat center armrest cover with pad.
88660C
11.INSTALL COOLER CONTROL SWITCH ASSEMBLY (for Center Seat)
Connect the 2 connectors.
Engage the 4 claws to install the cooler control switch assembly.
72830
12.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (for Center Seat)
Engage the 2 clips to install the rear seat center armrest assembly to the rear seat center armrest box assembly.
Engage the clamp.
72883A
13.INSTALL NO. 1 REAR SEAT CENTER ARMREST BRACKET (for Center Seat)
Install the No. 1 rear seat center armrest bracket with the 2 bushes and 2 bolts.
Engage the clamp.
14.INSTALL REAR CENTER SEATBACK FRAME WITH COVER AND PAD (for Center Seat)
Engage the 2 claws.
Install the rear center seatback frame with cover and pad with the 2 nuts.
87510P
15.INSTALL REAR SEATBACK HEATER ASSEMBLY LH (for LH Side)
w/ Seat Heater System:
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for Reclining Seat Type)>INSTALLATION
71078S
16.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for LH Side)
When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the 8 claws to install the separate type rear seatback cover to the separate type rear seatback pad.
Be careful not to damage the separate type rear seatback cover.
17.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly.
Engage the 13 hooks.
71931A
18.INSTALL REAR SEAT HEADREST SUPPORT (for LH Side)
|
Install in this Direction |
Engage the 4 claws to install the 2 rear seat headrest supports as shown in the illustration.
73344
19.INSTALL REAR SEAT SHOULDER BELT GUIDE LH (for LH Side)
Engage the guide.
Install the rear seat shoulder belt guide LH with the 2 screws.
87510Q
20.INSTALL REAR SEATBACK HEATER ASSEMBLY RH (for RH Side)
w/ Seat Heater System:
Use the same procedure as for the LH side.
71078S
21.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for RH Side)
Use the same procedure as for the LH side.
22.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Use the same procedure as for the LH side.
71931A
23.INSTALL REAR SEAT HEADREST SUPPORT (for RH Side)
Use the same procedure as for the LH side.
73343
24.INSTALL REAR SEAT SHOULDER BELT GUIDE RH (for RH Side)
Use the same procedure as for the LH side.
73345
25.INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE (for RH Side)
Engage the guide.
Install the rear seat center shoulder belt guide with the 2 screws.
71089A
26.INSTALL REAR SIDE SEATBACK COVER SUB-ASSEMBLY LH (for LH Side)
Install the rear side seatback cover sub-assembly LH to the rear side seatback pad LH.
27.INSTALL REAR SIDE SEATBACK COVER WITH PAD (for LH Side)
|
Install in this Direction |
Install the rear side seatback cover with pad to the rear side seatback frame sub-assembly LH as shown in the illustration.
Engage the 11 hooks.
71088A
28.INSTALL REAR SIDE SEATBACK COVER SUB-ASSEMBLY RH (for RH Side)
Use the same procedure as for the LH side.
29.INSTALL REAR SIDE SEATBACK COVER WITH PAD (for RH Side)
Use the same procedure as for the LH side.