Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (except 2AR-FE) › 2017.12–2018.08
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0326623 DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE) U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE)  TERMINALS OF ECU  


CHECK ECM (for A25A-FKS)


C370678N08
5.5,0.25 5.917,0.5 0.417,0.25 3.833,0.25 4.25,0.5 0.417,0.25 1.75,0.25 2.167,0.5 0.417,0.25 5.583,0.292 6.042,0.49 0.458,0.198 10 false A24 3.927,0.292 4.385,0.49 0.458,0.198 10 false C59 1.844,0.292 2.302,0.49 0.458,0.198 10 false C57

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A24-1 (BATT) - A24-10 (E1) G - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C59-23 (D) - A24-10 (E1) R - W-B D shift position signal Ignition switch ON, shift lever in D 11 to 14 V
Ignition switch ON, shift lever not in D Below 1 V
A24-14 (S) - A24-10 (E1) GR - W-B S shift position signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S Below 1 V
A24-21 (STP) - A24-10 (E1) SB - W-B Stop light switch signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A24-27 (CCS) - A24-28 (ECCS) R - BE Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
+RES switch pushed 235 to 245 Ω
-SET switch pushed 617 to 643 Ω
CANCEL switch pushed 1509 to 1571 Ω
A24-22 (ST1-) - A24-10 (E1) LG - W-B Stop light switch signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V
A24-19 (SFTD) - A24-10 (E1) W - W-B Down-shift position switch signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in "-" Below 1 V
A24-20 (SFTU) - A24-10 (E1) G - W-B Up-shift position switch signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in "+" Below 1 V


CHECK ECM (for 2GR-FKS)


A247842N91
2.458,0.354 2.854,0.594 0.396,0.24 5.906,0.354 6.302,0.594 0.396,0.24 2.542,0.396 2.948,0.625 0.406,0.229 10 false C96 5.979,0.396 6.385,0.656 0.406,0.26 10 false A23

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A23-1 (BATT) - C96-53 (E1) R - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C96-139 (D) - C96-53 (E1) R - W-B D shift position signal Ignition switch ON, shift lever in D 11 to 14 V
Ignition switch ON, shift lever not in D Below 1 V
A23-17 (S) - C96-53 (E1) GR - W-B S shift position signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S Below 1 V
A23-27 (STP) - C96-53 (E1) SB - W-B Stop light switch signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A23-41 (CCS) - C96-53 (E1) R - W-B Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
+RES switch pushed 235 to 245 Ω
-SET switch pushed 617 to 643 Ω
CANCEL switch pushed 1509 to 1571 Ω
A23-42 (ST1-) - C96-53 (E1) LG - W-B Stop light switch signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V
A23-37 (SFTD) - C96-53 (E1) W - W-B Down-shift position switch signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in "-" Below 1 V
A23-38 (SFTU) - C96-53 (E1) G - W-B Up-shift position switch signal Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in "+" Below 1 V


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


A402620N01
3.365,0.063 3.792,0.302 0.427,0.24 3.458,0.115 3.917,0.313 0.458,0.198 10 false A30

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A30-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A30-2 (CA2L) - A30-1 (SGND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
A30-3 (CA2H) - A30-1 (SGND) R - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A30-5 (CA1P) - A30-1 (SGND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A30-6 (CA1N) - A30-1 (SGND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
A30-8 (IGB) - A30-1 (SGND) R - W-B Power source Ignition switch ON 11 to 14 V

a.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A30-3 (CA2H) and A30-1 (SGND)

·

Between A30-5 (CA1P) and A30-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




b.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A30-2 (CA2L) and A30-1 (SGND)

·

Between A30-6 (CA1N) and A30-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.





CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the V6 forward recognition camera connector.



B472992N01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-7 (IGB) - V6-10 (GND) LA-P - LA Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
V6-5 (CA1P) - V6-10 (GND) L - LA CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
V6-11 (CA1N) - V6-10 (GND) W - LA CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
V6-6 (CANH) - V6-10 (GND) G - LA CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
V6-12 (CANL) - V6-10 (GND) W - LA CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
V6-3 (LKSW) - V6-10 (GND) V - LA Vehicle-to-vehicle distance control switch signal Ignition switch ON, vehicle-to-vehicle distance control switch not pushed 4.75 to 5.25 V
Ignition switch ON, vehicle-to-vehicle distance control switch pushed Below 1 V
V6-10 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω

a.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between V6-5 (CA1P) and V6-10 (GND)

·

Between V6-6 (CANH) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




b.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between V6-11 (CA1N) and V6-10 (GND)

·

Between V6-12 (CANL) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.