Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (except 2AR-FE) › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0326623 DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE)  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the millimeter wave radar sensor assembly when the ignition switch is ON.

WIRING DIAGRAM

A402116E02
0.375,0.906 3.438,1.104 3.063,0.198 10 false from IG1-NO. 1 Relay 2.677,1.063 4.667,1.26 1.99,0.198 10 false ECU-IG1 NO. 3 5.115,0.792 5.271,0.99 0.156,0.198 10 false 8 5.115,1.833 5.427,2.031 0.313,0.198 10 false 1 5.292,0.906 5.75,1.104 0.458,0.198 10 false IGB 5.281,1.958 5.74,2.156 0.458,0.198 10 false SGND 4.875,2.479 5.188,2.677 0.313,0.198 10 false A30 4.875,2.646 6.74,3.135 1.865,0.49 10 false Millimeter Wave Radar Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
a.
B471747C03
1.479,0.146 1.875,0.375 0.396,0.229 1.958,1.229 2.479,1.635 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 2.531,1.573 2.99,1.771 0.458,0.198 10 false IGB 1.563,0.177 2.177,0.375 0.615,0.198 10 false A30
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A30 millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Connect the A30 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
B471747C04
1.469,0.146 1.865,0.375 0.396,0.229 1.406,1.042 0.792,0.844 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.375,0.771 0.833,0.969 0.458,0.198 10 false SGND 1.552,0.177 2.167,0.375 0.615,0.198 10 false A30
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A30 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the A30 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR