Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0342029 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA1  FCM Destination Information Unmatched  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store vehicle information received from the main body ECU (multiplex network body ECU) and ECM. If the vehicle information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU) or ECM, DTC C1AA1 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA1 FCM Destination Information Unmatched After the engine switch is turned on (IG) for 3 seconds or more, vehicle information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) or ECM do not match for 5 seconds or more.
·

CAN communication system

·

Forward recognition camera

·

Main body ECU (Multiplex network body ECU)

·

ECM



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:

This DTC is stored when the vehicle information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) or ECM do not match. If the forward recognition camera, main body ECU (multiplex network body ECU) or ECM has been replaced, check if a forward recognition camera, main body ECU (multiplex network body ECU) or ECM from another vehicle was used.


PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
HINT:

When DTC C1AA1 is stored, forward recognition camera system DTC C1AAC may be stored at the same time.


a.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AAC is not output A
DTC C1AAC is output B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC U0142 is not output A
DTC U0142 is output B



A

3.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)

B

3.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 8 seconds or more.




c.

Check for DTCs.

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

B

4.REPLACE FORWARD RECOGNITION CAMERA
4.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
5.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 8 seconds or more.




c.

Check for DTCs.

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)