Home › Vehicle Interior › HEATING / AIR CONDITIONING › ECO SWITCH › 2017.12–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0322961 ECO SWITCH G

HEATING / AIR CONDITIONING  ECO SWITCH  INSPECTION  


PROCEDURE

Hide 84390B 1.INSPECT ECO SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for LHD)

C379195C20
1.458,0.302 1.917,0.563 0.458,0.26 0.917,1.833 1.198,1.396 true 2.083,1.833 1.948,1.396 true 1.948,1.125 2.333,0.542 true 1.333,1.135 0.875,0.573 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.563,0.354 1.875,0.552 0.313,0.198 10 false K37 0.719,0.396 1.031,0.594 0.313,0.198 10 false ILL- 2.271,0.365 2.583,0.563 0.313,0.198 10 false ILL+ 2.01,1.854 2.323,2.052 0.313,0.198 10 false ECU 0.792,1.833 1.25,2.031 0.458,0.198 10 false GND1
*a Component without harness connected
(ECO Switch Assembly (Electric Parking Brake Switch Assembly))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K37-11 (ECU) - K37-16 (GND1) ECO switch assembly (electric parking brake switch assembly) on (when switch is pressed) Below 10 Ω
E37-11 (ECU) - K37-16 (GND1) ECO switch assembly (electric parking brake switch assembly) off (when switch is not pressed) 100 kΩ or higher



b.

Check that the switch illuminates.

i.

Apply battery voltage to the ECO switch assembly (electric parking brake switch assembly) and check that the switch illuminates.

OK:
Tester Connection Specified Condition
Battery positive (+) → K37-3 (ILL+)
Battery negative (-) → K37-7 (ILL-)
Illuminates




Hide 84390B 2.INSPECT ECO SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for RHD)

C379195C16
1.458,0.302 1.917,0.563 0.458,0.26 1.208,1.833 1.49,1.396 true 2.646,1.813 2.292,1.396 true 2.125,1.135 2.51,0.552 true 1.458,1.125 1,0.563 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.563,0.354 1.875,0.552 0.313,0.198 10 false K37 2.448,0.375 2.76,0.573 0.313,0.198 10 false ILL- 0.865,0.385 1.177,0.583 0.313,0.198 10 false ILL+ 1.021,1.844 1.333,2.042 0.313,0.198 10 false ECU 2.542,1.833 3,2.031 0.458,0.198 10 false GND1
*a Component without harness connected
(ECO Switch Assembly (Electric Parking Brake Switch Assembly))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K37-14 (ECU) - K37-9 (GND1) ECO switch assembly (electric parking brake switch assembly) on (when switch is pressed) Below 10 Ω
E37-14 (ECU) - K37-9 (GND1) ECO switch assembly (electric parking brake switch assembly) off (when switch is not pressed) 100 kΩ or higher



b.

Check that the switch illuminates.

i.

Apply battery voltage to the ECO switch assembly (electric parking brake switch assembly) and check that the switch illuminates.

OK:
Tester Connection Specified Condition
Battery positive (+) → K37-6 (ILL+)
Battery negative (-) → K37-2 (ILL-)
Illuminates