Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2017.12
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0322782 AUTOMATIC TRANSAXLE SYSTEM C

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open When the ignition switch is ON and battery voltage is 8 V or more, NSW, P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic).
·

Park/neutral position switch assembly

·

Open in park/neutral position switch assembly circuit

·

ECM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure When the ignition switch is ON and battery voltage is 8 V or more, 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic).
·

NSW, P or N input signal

·

R input signal

·

D input signal


·

Park/neutral position switch assembly

·

Short in park/neutral position switch assembly circuit

·

ECM


Comes on DTC stored SAE Code:
P0705

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○
Malfunction Condition NSW input signal is ON ○ ○ - -
P input signal is ON - - ○ ○
R input signal is ON - ○ - ○
N input signal is ON - - - -
D input signal is ON ○ - ○ -
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnostic Condition Ignition switch is ON ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○
Malfunction Condition NSW input signal is ON - - -
P input signal is ON - - -
R input signal is ON - ○ ○
N input signal is ON ○ ○ -
D input signal is ON ○ - ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

DTC P070562 is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will then illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each with the ignition switch ON.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: P070513 or P070562.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C374269E01
2.615,3.979 3.958,4.385 1.344,0.406 10 false Park/Neutral Position Switch Assembly 0.729,0.948 2.417,1.146 1.688,0.198 10 false to ST Relay 0.198,1.688 2.646,1.885 2.448,0.198 10 false from ECU-ACC Fuse 0.219,2.479 2.667,2.677 2.448,0.198 10 false from BKUP LP Fuse 5.333,0.854 5.792,1.052 0.458,0.198 10 false NSW 5.333,1.458 5.792,1.656 0.458,0.198 10 false P 5.333,2.063 5.792,2.26 0.458,0.198 10 false R 5.344,2.656 5.802,2.854 0.458,0.198 10 false N 5.344,3.26 5.802,3.458 0.458,0.198 10 false D 4.948,3.375 5.406,3.573 0.458,0.198 10 false C59 5,3.167 5.458,3.365 0.458,0.198 10 false 23 4.99,2.563 5.448,2.76 0.458,0.198 10 false 24 4.979,1.969 5.438,2.167 0.458,0.198 10 false 25 4.979,1.365 5.438,1.563 0.458,0.198 10 false 26 4.99,0.76 5.448,0.958 0.458,0.198 10 false 23 2.552,0.854 3.01,1.052 0.458,0.198 10 false 9 2.573,2.375 3.031,2.573 0.458,0.198 10 false 1 2.781,2.375 3.24,2.573 0.458,0.198 10 false RB 2.802,0.854 3.26,1.052 0.458,0.198 10 false L 3.552,0.854 4.01,1.052 0.458,0.198 10 false B 3.49,1.458 3.948,1.656 0.458,0.198 10 false PL 3.5,2.063 3.958,2.26 0.458,0.198 10 false RL 3.49,2.656 3.948,2.854 0.458,0.198 10 false NL 3.49,3.26 3.948,3.458 0.458,0.198 10 false DL 3.802,3.26 4.26,3.458 0.458,0.198 10 false 7 3.781,2.656 4.24,2.854 0.458,0.198 10 false 8 3.792,2.063 4.25,2.26 0.458,0.198 10 false 2 3.792,1.458 4.25,1.656 0.458,0.198 10 false 3 3.792,0.854 4.25,1.052 0.458,0.198 10 false 4 2.604,3.813 3.063,4.01 0.458,0.198 10 false C55 5.729,4.073 6.188,4.271 0.458,0.198 10 false ECM 5.99,0.698 6.448,0.896 0.458,0.198 10 false 12 V 4.948,2.781 5.406,2.979 0.458,0.198 10 false C59 4.948,2.177 5.406,2.375 0.458,0.198 10 false C59 4.938,1.583 5.396,1.781 0.458,0.198 10 false C59 4.938,0.969 5.396,1.167 0.458,0.198 10 false A24

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the C55 park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C55-1 (RB) - Body ground Ignition switch ON 11 to 14 V
C55-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.

Disconnect the C55 park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C55-4 (B) - Body ground Ignition switch ON 11 to 14 V
C55-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C83
1.823,0.958 2.135,0.385 true 1.594,0.958 1.75,0.354 true 1.271,0.948 0.833,0.375 true 1.313,1.792 1.49,1.292 true 2,1.781 1.719,1.292 true 0.865,1.781 1.344,1.281 true 1.385,0.938 1.198,0.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.708,0.292 0.865,0.49 0.156,0.198 10 false B 1.813,0.292 2.063,0.49 0.25,0.198 10 false RL 2.198,0.302 2.448,0.5 0.25,0.198 10 false RB 0.771,1.74 1.021,1.938 0.25,0.198 10 false L 2.063,1.74 2.313,1.938 0.25,0.198 10 false DL 1.146,1.75 1.396,1.948 0.25,0.198 10 false NL 1,0.271 1.417,0.469 0.417,0.198 10 false PL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the C55 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
1 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
4 (B) - 9 (L) Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Connect the C55 park/neutral position switch assembly connector.


b.

Disconnect the C59 ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C59-26 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
C59-25 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
C59-24 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
C59-23 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D, S, "+" or "-"


11 to 14 V
C59-26 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
C59-25 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
C59-24 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
C59-23 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D, S, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back up lights.



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the C55 park/neutral position switch assembly connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-4 (B) - A24-23 (NSW) Always Below 1 Ω
C55-4 (B) or A24-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT