Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2017.12
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0322782 AUTOMATIC TRANSAXLE SYSTEM C

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P074011  Torque Converter Clutch Circuit Short to Ground  


DESCRIPTION

Solenoid (SL) valve is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P074011 Torque Converter Clutch Circuit Short to Ground While the vehicle is being driven so that lock-up is not requested, a short to ground is detected in the solenoid (SL) valve circuit (2-trip detection logic).
·

Solenoid (SL) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P2769

Fail-safe function:

If the ECM detects a malfunction, it turns Solenoid (SL) valve off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to solenoid (SL) valve to regulate the hydraulic pressure and provide smoother torque converter engagement. Solenoid (SL) valve responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects a short to ground in the solenoid (SL) valve circuit, it will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P074011.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C380523E04
1.479,1.688 4.385,1.885 2.906,0.198 10 false Solenoid (SL) Valve 1.615,2.792 4.521,2.99 2.906,0.198 10 false Transmission Wire 1.625,2.646 4.531,2.844 2.906,0.198 10 false C93 5.656,3.052 6.313,3.271 0.656,0.219 10 false ECM 5.646,2.896 6.302,3.115 0.656,0.219 10 false C59 5.802,0.854 6.458,1.073 0.656,0.219 10 false 12 V 3.313,1.125 3.969,1.344 0.656,0.219 10 false S1 3.604,1.125 4.26,1.344 0.656,0.219 10 false 13 4.896,1.115 5.552,1.333 0.656,0.219 10 false 19 5.177,1.115 5.833,1.333 0.656,0.219 10 false SL

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SOLENOID (SL) VALVE)
a.
C361126C06
2.146,1.042 2.5,0.25 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.552,0.177 2.865,0.375 0.313,0.198 10 false S1
*a Component without harness connected
(Transmission Wire)


Disconnect the C93 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (S1) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the C93 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.INSPECT SOLENOID (SL) VALVE
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C59 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C59-19 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.INSPECT SOLENOID (SL) VALVE
a.
C361133C01
0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 2.583,0.24 3.042,0.438 0.458,0.198 10 false (+) 1.594,0.26 2.052,0.458 0.458,0.198 10 false (-)
*1 Solenoid (SL) Valve


Remove the solenoid (SL) valve.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG