Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST PIPE › from 2017.12
RM33A0E _51 Engine / Hybrid System _065336 2GR-FKS INTAKE / EXHAUST _0328630 EXHAUST PIPE A

2GR-FKS INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly (TWC: Rear Catalyst), center exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A412413

Remove the 2 bolts and disconnect the tail exhaust pipe assembly from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 17440 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY LH

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A412412

Remove the 2 bolts and disconnect the tail exhaust pipe assembly LH from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly LH from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 57533B 3.REMOVE FRONT CENTER FLOOR BRACE

a.
A408253

Remove the 4 bolts and front center floor brace from the vehicle body.


Hide 57523A 4.REMOVE CENTER FLOOR CROSSMEMBER BRACE

a.
A408254

Remove the 4 bolts and center floor crossmember brace from the vehicle body.


Hide 17420 5.REMOVE CENTER EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A408256

Remove the 2 bolts, 2 nuts and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Remove the center exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 52239B 6.REMOVE BODY MOUNTING PLATE

a.
A408255

Remove the 6 bolts and body mounting plate.


Hide 17584B 7.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

a.
A408257

Remove the 2 nuts and No. 1 exhaust pipe support bracket (for Lower Side).


Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A408145

Disconnect the 2 heated oxygen sensor connectors.


b.

Disengage the 2 wire harness clamps.


c.
A408258

Remove the 2 bolts, 2 nuts and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold LH (TWC: Front Catalyst) and exhaust manifold RH (TWC: Front Catalyst).


d.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust pipe support.


e.

Remove the 2 gaskets from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 89465 9.REMOVE HEATED OXYGEN SENSOR (for Bank 1)

Hide 89465A 10.REMOVE HEATED OXYGEN SENSOR (for Bank 2)

Hide 17408 11.REMOVE TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.

·

Use the same procedure as for the tail exhaust pipe assembly LH.



a.
A408269

Type A:

i.

Remove the tail exhaust pipe baffle sub-assembly.



b.
A402255

Type B:

i.

Remove the tail exhaust pipe baffle sub-assembly.