Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › EXHAUST PIPE › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328641 EXHAUST PIPE A

2AR-FE INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly (TWC: Rear Catalyst), center exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402248

Remove the 2 bolts and disconnect the tail exhaust pipe assembly from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 17440 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY LH (for Dual Type)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A408250

Remove the 2 bolts and disconnect the tail exhaust pipe assembly LH from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly LH from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 17420 3.REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Single Type)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A407118

Remove the 2 bolts, 2 compression springs and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Remove the center exhaust pipe assembly from the exhaust pipe support.


c.

Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 17420 4.REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Dual Type)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A407119

Remove the 2 bolts, 2 compression springs and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Remove the center exhaust pipe assembly from the exhaust pipe support.


c.

Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 57533B 5.REMOVE FRONT CENTER FLOOR BRACE

a.
A402319

Remove the 4 bolts and front center floor brace from the vehicle body.


Hide 57523A 6.REMOVE CENTER FLOOR CROSSMEMBER BRACE

a.
A402320

Remove the 4 bolts and center floor crossmember brace from the vehicle body.


Hide 52239B 7.REMOVE BODY MOUNTING PLATE

a.
A412398

Remove the 6 bolts and body mounting plate.


Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A407122

Remove the 2 bolts, 2 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


b.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


c.

Remove the gasket from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 17408 10.REMOVE TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.

·

Use the same procedure as for the tail exhaust pipe assembly LH (for Dual Type).



a.
A408269

Type A (w/ Tail Exhaust Pipe Baffle):

i.

Remove the tail exhaust pipe baffle sub-assembly.



b.
A402255

Type B:

i.

Remove the tail exhaust pipe baffle sub-assembly.