Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › EXHAUST PIPE › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328641 EXHAUST PIPE A

2AR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17408 1.INSTALL TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.

·

Use the same procedure as for the tail exhaust pipe assembly LH (for Dual Type).



a.
A483297C01
2.469,1.583 2.469,0.833 2.469,0.833 2.604,0.74 true 2.146,1.594 1.531,1.594 1.531,1.594 1.531,1.802 true 2.906,1.583 2.906,0.833 2.906,0.833 3.063,0.74 true 2.667,0.656 2.896,0.865 0.229,0.208 10 false *a 1.458,1.844 1.656,2.042 0.198,0.198 10 false *c 3.104,0.667 3.333,0.875 0.229,0.208 10 false *b
*a Protrusion
*b Cutout


Type A (w/ Tail Exhaust Pipe Baffle):

i.

Align the cutout of a new tail exhaust pipe baffle sub-assembly with the protrusion of the tail exhaust pipe assembly as shown in the illustration.


ii.

Using a plastic hammer, uniformly tap the tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.


iii.

Check that the cutout of the tail exhaust pipe baffle sub-assembly is aligned with the protrusion on the bottom of the tail exhaust pipe assembly.



b.
A483298C01
2.823,1.333 2.938,0.917 2.938,0.917 3.146,0.917 true 0.667,1.604 0.865,1.604 0.865,1.604 0.958,1.49 true 1.896,1.573 2.719,1.573 true 2.104,1.875 2.51,1.875 2.51,1.875 2.813,1.604 true 3.188,0.844 3.417,1.052 0.229,0.208 10 false *a 1.698,1.5 1.896,1.698 0.198,0.198 10 false *c 0.49,1.552 0.688,1.75 0.198,0.198 10 false *d 1.896,1.813 2.125,2.021 0.229,0.208 10 false *b
*a Guide Line
*b Cutout


Type B:

i.

Align the cutout of a new tail exhaust pipe baffle sub-assembly with the guide line of the tail exhaust pipe assembly as shown in the illustration.


ii.

Using a plastic hammer, uniformly tap the tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.



Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A310336C02
0.865,0.219 1.073,0.219 1.073,0.219 1.156,0.594 false 0.75,1.156 0.938,1.156 0.938,1.156 1.094,0.885 false 2.688,0.146 2.469,0.146 2.469,0.146 2.406,0.771 true 0.677,0.156 0.99,0.313 0.313,0.156 10 false *1 0.573,1.083 0.885,1.24 0.313,0.156 10 false *2 2.75,0.073 3.063,0.229 0.313,0.156 10 false *3 0.271,0.688 0.583,0.844 0.313,0.156 10 false *a
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 52239B 4.INSTALL BODY MOUNTING PLATE

a.

Install the body mounting plate with the 6 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 57523A 5.INSTALL CENTER FLOOR CROSSMEMBER BRACE

a.

Install the center floor crossmember brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 57533B 6.INSTALL FRONT CENTER FLOOR BRACE

a.

Install the front center floor brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 17420 7.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the center exhaust pipe assembly to the exhaust pipe support.


e.

Install the center exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A415472C01
2.302,0.813 2.521,0.229 2.521,0.229 2.875,0.229 true 0.677,1.49 0.677,1.146 0.677,1.146 0.969,0.927 false 0.531,0.24 0.708,0.24 0.708,0.24 0.969,0.667 false 0.375,0.177 0.635,0.375 0.26,0.198 10 false *1 0.625,1.531 0.938,1.688 0.313,0.156 10 false *2 2.906,0.188 3.146,0.375 0.24,0.188 10 false *3 0.271,1.5 0.583,1.656 0.313,0.156 10 false *a
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Center Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and center exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 17430 8.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the center exhaust pipe assembly.


b.

Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17440 9.INSTALL TAIL EXHAUST PIPE ASSEMBLY LH (for Dual Type)

a.

Install a new gasket to the center exhaust pipe assembly.


b.

Connect the tail exhaust pipe assembly LH to the 2 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly LH to the center exhaust pipe assembly with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 10.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION