Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2017.12–2019.10
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Accessory Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Accessory Gateway ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Local Bus Gateway" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Local Bus Gateway" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Local Bus Gateway" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Accessory Gateway ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Accessory gateway ECU (network gateway ECU) branch line or connector

·

Power source circuit of accessory gateway ECU (network gateway ECU)

·

Accessory gateway ECU (network gateway ECU) ground circuit

·

Accessory gateway ECU (network gateway ECU)



WIRING DIAGRAM

C392481E01
0.208,1.938 0.833,2.229 0.625,0.292 10 false K127 0.615,1.938 2.792,2.26 2.177,0.323 10 false No. 4 CAN Junction Connector 1.719,1.448 2.344,1.74 0.625,0.292 10 false 19 1.75,0.865 2.375,1.156 0.625,0.292 10 false 8 5.354,0.865 5.979,1.156 0.625,0.292 10 false 16 5.354,1.458 5.979,1.75 0.625,0.292 10 false 15 5.667,0.979 6.292,1.271 0.625,0.292 10 false CA1H 5.667,1.573 6.292,1.865 0.625,0.292 10 false CA1L 5.677,2.469 6.302,2.76 0.625,0.292 10 false IG1 5.354,2.333 5.979,2.625 0.625,0.292 10 false 10 3.875,2.292 5.031,2.573 1.156,0.281 10 false ECU-IG1 NO. 4 1.719,2.448 3.26,2.865 1.542,0.417 10 false from IG1-NO. 1 Relay 1.719,3.281 3.26,3.573 1.542,0.292 10 false from IG2-NO. 2 Relay 3.906,3.125 5.052,3.406 1.146,0.281 10 false ECU-IG2 NO. 3 5.417,3.177 6.042,3.469 0.625,0.292 10 false 9 5.667,3.292 6.292,3.583 0.625,0.292 10 false IG2 5.656,4.125 6.281,4.417 0.625,0.292 10 false GND 5.417,4 6.042,4.292 0.625,0.292 10 false 4 5.146,4.771 5.771,5.063 0.625,0.292 10 false K140 5.531,4.771 7.135,5.323 1.604,0.552 10 false Accessory Gateway ECU (Network Gateway ECU)

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ACCESSORY GATEWAY ECU (NETWORK GATEWAY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the K140 accessory gateway ECU (network gateway ECU) connector.


c.
C379529C07
1.406,0.406 1.854,0.667 0.448,0.26 2.583,1.958 2.583,2.708 2.583,2.708 2.75,2.708 true 2.417,1.958 2.417,2.708 2.417,2.708 2.25,2.708 true 1.479,0.458 2.094,0.656 0.615,0.198 10 false K140 2.844,2.635 3.292,2.833 0.448,0.198 10 false CA1H 1.844,2.635 2.292,2.833 0.448,0.198 10 false CA1L 0.167,0.135 0.781,0.333 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Accessory Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K140-16 (CA1H) - K140-15 (CA1L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ACCESSORY GATEWAY ECU (NETWORK GATEWAY ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C379529C09
1.406,0.406 1.854,0.667 0.448,0.26 1.542,1.958 1.542,2.708 1.542,2.708 1.708,2.708 true 1.375,1.958 1.375,2.708 1.375,2.708 1.208,2.708 true 2.406,1.604 2.406,0.938 2.406,0.938 2.573,0.938 true 1.49,0.458 2.104,0.656 0.615,0.198 10 false K140 1.813,2.646 2.26,2.844 0.448,0.198 10 false IG1 0.927,2.646 1.375,2.844 0.448,0.198 10 false IG2 0.167,0.135 0.781,0.333 0.615,0.198 10 false *a 2.656,0.875 3.104,1.073 0.448,0.198 10 false GND
*a Front view of wire harness connector
(to Accessory Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K140-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K140-9 (IG2) - Body ground Ignition switch ON 11 to 14 V
K140-10 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE ACCESSORY GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)