Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › from 2017.12
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328236 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Entry Exterior Alarm and Answer-back Buzzer do not Sound  


DESCRIPTION

The smart entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.

WIRING DIAGRAM

B388643E34
2.354,1.031 2.813,1.229 0.458,0.198 10 false 3C 0.427,1.438 0.885,1.635 0.458,0.198 10 false A16 0.417,1.604 1.677,2.01 1.26,0.406 10 false Wireless Door Lock Buzzer 2.354,0.865 2.813,1.063 0.458,0.198 10 false 29 3.677,0.865 4.135,1.063 0.458,0.198 10 false 21 3.646,1.042 4.104,1.24 0.458,0.198 10 false MB 3.958,0.938 4.417,1.135 0.458,0.198 10 false BZR 4.271,0.542 4.729,0.74 0.458,0.198 10 false +B 1.719,0.958 1.948,1.146 0.229,0.188 10 false 1 0.5,0.948 0.729,1.135 0.229,0.188 10 false 2 2.271,1.583 3.885,2.01 1.615,0.427 10 false Instrument Panel Junction Block Assembly 5.531,2.677 7.073,3.198 1.542,0.521 10 false Certification ECU (Smart Key ECU Assembly) 0.646,3.219 2.417,3.458 1.771,0.24 10 false : CAN Communication Line 3.51,2.698 5.177,3.104 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.

Wireless Door Lock
Tester Display Description Default Setting ECU
Wireless Buzzer Resp Wireless buzzer response* ON 0:OFF,1:ON Main body ECU (multiplex network body ECU)
50006 1

*: w/ Wireless Door Lock Buzzer Answer-back Function



Result:
Result Proceed to
"ON" is displayed A
"OFF" is displayed B



A

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)

B

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door RH unlocked
LOCK: Front door RH locked
-
FL Door Lock Pos Front door LH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door LH unlocked
LOCK: Front door LH locked
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON OFF: Rear door RH locked
ON: Rear door RH unlocked
-
RL-Door Lock Pos SW Rear door LH unlock detection switch signal OFF or ON OFF: Rear door LH locked
ON: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
OK:

The GTS display changes correctly in response to the lock/unlock operation.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)