Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2017.12
RM33A0E _59 Vehicle Exterior _065391 SLIDING ROOF / CONVERTIBLE _0345531 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch (roof console box sub-assembly) is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch (roof console box sub-assembly) is stuck for 30 seconds or more
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Roof console box sub-assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch Failure(Past) Open switch failure signal (Past) OFF or ON OFF: No sliding roof open switch failure signal (Past)
ON: Sliding roof open switch failure signal (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past) OFF or ON OFF: No sliding roof close switch failure signal (Past)
ON: Sliding roof close switch failure signal (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past) OFF or ON OFF: No sliding roof tilt up switch failure signal (Past)
ON: Sliding roof tilt up switch failure signal (Past)
-
Down Switch Failure(Past) Down switch failure signal (Past) OFF or ON OFF: No sliding roof tilt down switch failure signal (Past)
ON: Sliding roof tilt down switch failure signal (Past)
-
Open Switch Failure(Current) Open switch failure signal (Current) OFF or ON OFF: No sliding roof open switch failure signal (Current)
ON: Sliding roof open switch failure signal (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current) OFF or ON OFF: No sliding roof close switch failure signal (Current)
ON: Sliding roof close switch failure signal (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current) OFF or ON OFF: No sliding roof tilt up switch failure signal (Current)
ON: Sliding roof tilt up switch failure signal (Current)
-
Down Switch Failure(Current) Down switch failure signal (Current) OFF or ON OFF: No sliding roof tilt down switch failure signal (Current)
ON: Sliding roof tilt down switch failure signal (Current)
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch Failure(Past)
Close Switch Failure(Past)
Up Switch Failure(Past)
Down Switch Failure(Past)
Open Switch Failure(Current)
Close Switch Failure(Current)
Up Switch Failure(Current)
Down Switch Failure(Current)
50003 147 32,33,34,35,36,37,38,39
OK:

OFF is displayed for each Data List item.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - BODY GROUND)
a.

Disconnect the V19 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Disconnect the V14 sliding roof switch (roof console box sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V19-10 (OPN) or V14-5 (OPN) - Body ground Always 10 kΩ or higher
V19-8 (CLS) or V14-4 (CLS) - Body ground Always 10 kΩ or higher
V19-5 (OPN) or V14-3 (UP) - Body ground Always 10 kΩ or higher
V19-9 (CLS) or V14-18 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Remove the sliding roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the sliding roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)