Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0319642 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The forward recognition camera receives vehicle stability signals from the yaw rate sensor (airbag sensor assembly). If the yaw rate sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a signal from the yaw rate sensor (airbag sensor assembly) indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Forward recognition camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a signal from the yaw rate sensor (airbag sensor assembly) indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

Forward recognition camera system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the vehicle stability control system. Therefore it is necessary to check for and troubleshoot vehicle stability control system DTCs first.


a.

Check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

B

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the ignition switch to ON and wait 3 seconds or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.




c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

B

REPLACE FORWARD RECOGNITION CAMERA