Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0319642 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0101  Lost Communication with TCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U0131  Lost Communication with Power Steering Control Module  U0142  Lost Communication with Body Control Module "B"  U0155  Lost Communication with Instrument Panel Cluster (IPC) Control Module  


DESCRIPTION

When a malfunction is detected between various ECUs and sensors, these DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A" After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a communication error between the ECM and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

ECM

·

Forward recognition camera


U0101 Lost Communication with TCM After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a communication error between the TCM (ECM) and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

TCM (ECM)

·

Forward recognition camera


U0123 Lost Communication with Yaw Rate Sensor Module After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a communication error between the yaw rate sensor (airbag sensor assembly) and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Yaw rate sensor (Airbag sensor assembly)

·

Forward recognition camera


U0126 Lost Communication with Steering Angle Sensor Module After the ignition switch is turned to ON for 3 seconds or more, a communication error between the steering sensor and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Steering sensor

·

Forward recognition camera


U0129 Lost Communication with Brake System Control Module After the ignition switch is turned to ON for 3 seconds or more, a communication error between the skid control ECU (brake actuator assembly) and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Forward recognition camera


U0131 Lost Communication with Power Steering Control Module After the ignition switch is turned to ON for 3 seconds or more, a communication error between the power steering ECU (rack and pinion power steering gear assembly) and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Power steering ECU (Rack and pinion power steering gear assembly)

·

Forward recognition camera


U0142 Lost Communication with Body Control Module "B" After the ignition switch is turned to ON for 3 seconds or more, a communication error between the main body ECU (multiplex network body ECU) and forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera


U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module After the ignition switch is turned to ON for 3 seconds or more, a communication error between the combination meter assembly and forward recognition camera is detected for approximately 50 seconds or more.
·

CAN communication system

·

Combination meter assembly

·

Forward recognition camera



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the ignition switch to ON and wait 1 minute or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.




c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC U0100, U0101, U0123, U0126, U0129, U0131, U0142 and U0155 are not output A
DTC U0100, U0101, U0123, U0126, U0129, U0131, U0142 or U0155 is output B



A

B