The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication. If there is a communication error with the forward recognition camera, the millimeter wave radar sensor assembly stores DTC U023A.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U023A | Lost Communication With Image Processing Module "A" | When the ignition switch is ON, a communication error between the forward recognition camera and millimeter wave radar sensor assembly is detected for approximately 2 seconds. | ·
CAN communication system ·
Forward recognition camera power source circuit ·
Forward recognition camera ·
Wire harness or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: System Select / Can Bus Check.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 2 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is not output | A |
| DTC U1002 is output | B |
A
B
Disconnect the V6 forward recognition camera connector.
Disconnect the A30 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - A30-5 (CA1P) | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| V6-12 (CANL) - A30-6 (CA1N) | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Connect the A30 millimeter wave radar sensor assembly connector.
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the V6 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-10 (GND) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-7 (IGB) - Body ground | Ignition switch ON | 11 to 14 V |
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG